background image

15

Tighten couplings

3. 

Using pliers, tighten the couplings with additional two-thirds  

turn.

noTE:

 Do not overtighten. Damage to the coupling can result.

Attach short hose and  

“Y” connector

2. 

If space permits, attach the brass female end of the “Y” 

connector to the cold water faucet. See figure A.

If “Y” connector cannot be attached directly to the cold water 

faucet, the short hose must be used. See figure B. Attach short 

hose to cold water faucet. Screw on coupling by hand until it is 

seated on faucet. Then attach “Y” connector to brass male end 

of the short hose. Screw on coupling by hand until it is seated  

on connector.

Fig. A

Fig. B

Attach long hose to “Y”  

connector and tighten couplings

4. 

One end of the long hose has a wire mesh strainer inside the  

coupling. Attach this end to the “Y” connector. Attach washer 

cold inlet hose to other side of “Y” connector. Screw on 

coupling by hand until it is seated on connector. Using pliers, 

tighten the couplings an additional two-thirds turn.

noTE:

 Do not overtighten. Damage to the coupling can result.

Attach long hose to dryer fill 

valve and tighten coupling

5. 

Attach other end of long hose to fill 

valve at bottom of dryer back panel. 

Screw on coupling by hand until it  

is seated on fill valve connector. 

Using pliers, tighten the couplings 

an additional two-thirds turn.

noTE:

 Do not overtighten. Damage to the coupling can result.

Turn on cold water faucet

Check that the water faucets are turned on.

Check for leaks

Check for leaks around “Y” connector, faucets, and hoses.

6. 

7. 

Summary of Contents for MEDB200VQ - Bravos Series 29-in Electric Dryer





















Reviews: