background image

Hot Water Dispenser

A Note to You

Please read the Installation Instructions
and Use and Care Guide. It contains
important information about how to install,
operate and maintain your hot water
dispenser properly and safely. Please
read it carefully.

Also, please complete and mail the
Product Registration Card provided
with your hot water dispenser. This card
helps us notify you about any new
information for your hot water dispenser.

Part No. 3192760

Record your model’s information

Write down the following information about your hot water dispenser to better
help you obtain assistance or service if you ever need it. You will need to know
your complete model number and serial number. You can find this information
on the model and serial number label/plate.

If you need assistance or service, first see the “Troubleshooting” section of this
book. After checking “Troubleshooting,” additional help can be found by
checking the “Requesting Assistance or Service” section.

Builder/dealer name

Address

Phone number

Model number

Serial number

Purchase date

Date installed

(See the “Parts and Features” section for model and serial number label/plate
location.)

Keep this book and your sales slip together for future reference.

Installation

Instructions 

AND

Use and Care

Guide

IMPORTANT:
Read and save these instructions.

IMPORTANT:
Installer: 
Leave this guide with
homeowner.

Homeowner: Keep this guide for
future reference. Save this guide for
local electrical inspector’s use.

®

Summary of Contents for HD1000XSC7

















Reviews: