background image

20

WRINKLE SHIELD™ Feature

The WRINKLE SHIELD™ feature light illuminates when this 
option is selected. This indicator stays on with the Cycle 
Complete light.

Indicator lights

Other indicator lights on the control panel show when Cycle, 
Temp Adjust, and End of Cycle settings are selected. 

Cycles

Select the drying cycle that matches the type of load you are 
drying. See Auto Preset or Manual Preset Cycle Settings charts.

Cycle control knob

Auto Cycles

Auto Cycles allow you to match the cycle to the load you are 
drying. See the following Auto Preset Cycle Settings chart. Each
cycle dries certain fabrics at the recommended temperature. A
sensor detects the moisture in the load and automatically adjusts 
the drying time for optimal drying.

Heavy Duty

Use this cycle to get High heat for heavyweight mixed loads, 
cotton towels, or jeans.

Normal

Use this cycle to get Medium heat for drying mixed loads and 
sturdy fabrics such as work clothes. 

Casual

Use this cycle to get Low heat for drying no-iron fabrics such as
sport shirts, casual business clothes, and permanent press
blends.

Delicate

Use this cycle to get Low heat for drying synthetic fabrics, 
washable knit fabrics, and no-iron finishes. 

Super Delicate

Use this cycle to get Extra Low heat to gently dry items such as
lingerie, exercise wear, or sheer curtains. 

Damp Dry

Use this cycle to dry items to a damp level using Low heat, or to
dry items that do not require an entire drying cycle. Damp dry
items such as jeans (to avoid stiffness) or cotton clothing (to 
make ironing easier). The temperature setting on this cycle 
cannot be adjusted. Items will have different levels of dampness. 
At the end of this cycle, clothes will be damp.

Auto Preset Cycle Settings

*Estimated Time with Auto DRYNESS (Normal) setting.

Time will vary depending on load type and load size.

Manual Cycles

Use Manual Cycles to select a specific amount of drying time and 
a drying temperature. When a Manual Cycle is selected, the 
ESTIMATED TIME REMAINING display shows the actual time 
remaining in your cycle. You can change the actual time in the 
cycle by pressing TIMING Up or Down. 

Timed Dry

Use this cycle to complete drying if items are still damp after an 
Auto Cycle. Timed Dry is also useful for drying heavyweight and 
bulky items such as bedspreads and work clothes. 

Quick Dry

Use this cycle for drying small loads or loads that need a short
drying time.

Touch Up

Use this setting to help smooth out wrinkles from such items as 
clothes packed in a suitcase or items wrinkled from being left in 
the dryer too long.

Manual Preset Cycle Settings

*The Timed Dry cycle will default to the last temperature used for

Timed Dry.

Auto Cycles
Load Type

Temp.

Time*
(Minutes)

HEAVY DUTY

Heavyweight mixed loads, 
cotton towels, jeans 

High

40

NORMAL

Mixed loads, corduroys,  
work clothes, sheets

Medium

35

CASUAL

Permanent press, synthetics

Low

35

DELICATE

Lightweight items, blouses, 
synthetics

Low

30

SUPER DELICATE

Lingerie

Extra Low

25

DAMP DRY

Clothes to come out suitable 
for ironing

Low

20

Manual Cycles
Load Type

Temp.

Default Time
(Minutes)

TIMED DRY

 

Heavyweight, bulky items,
bedspreads, work clothes

High*

40

QUICK DRY

Small loads

Medium

27

TOUCH UP

 

Helps smooth out wrinkles

Medium

20

Summary of Contents for DUET SPORT W10151580B





























Reviews: