Whirlpool CFS810W, Installation Manual

Page: 2 / 14

4
BEFORE INSTALLING THE REFRIGERATOR
Foreword
Your new appliance is a FULL NO FROST model
exclusively for domestic use, i.e. both refrigerator
and freezer compartments are provided with an
automatic defrosting function.
This manual contains indications and warnings for
correct and safe installation of the appliance - read
it carefully before starting installation operations.
The model you have purchased may differ slightly
with respect to some descriptions in this manual,
since this manual covers several models.
Keep this manual for future consultation. If you sell
the appliance give it to the new buyer.
Declaration of conformity
This appliance is intended to come into contact
with foodstuffs and conforms to D.L. 108 of
25.01.1992 (European Directive 89/109/EEC).
Disposal of packaging materials
The packaging material for the protection and
transport of the appliance and single components is
entirely recyclable, and marked with the recycling
symbol .
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children, as
they are potentially dangerous.
Disposal must be carried out in accordance with
local regulations for waste disposal.
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
After unpacking the appliance, check for damage
and make sure that the doors shut properly. Any
damage must be reported to your retailer within
24 hours after delivery of the appliance.
Be careful not to damage the floors when you move
the appliance (e.g. parquet flooring). If, after
removing the doors, it is necessary to move the
appliance, make sure the internal components are
well secured and/or remove them in order to avoid
damage.
Because of the weight of the appliance, at least 2
persons are required to safely move/install it.
Installation of the appliance must be carried out by
a qualified technician.
Wait at least 1 hour before connecting the
appliance to the power supply in order to ensure
the refrigerant circuit is fully efficient.
Depending on the model purchased, the appliance
does not contain CFCs (if the refrigerant circuit
contains R134a) or HFCs (if the refrigerant circuit
contains R600a - Isobutane. Isobutane is a natural
gas with low environmental impact. Caution is
required, however, since isobutane is flammable.
Therefore, it is essential to ensure that refrigerant
pipelines are not damaged.
Data regarding refrigerant and insulating substances
is given on the rating plate.
Clean the inside of the appliance before introducing
food.
For correct and safe operation, install and connect
the appliance according to the instructions given in
this manual.
The appliance is set for optimum operation at
specific ambient temperature ranges, according to
the climatic class indicated on the data plate:
The appliance may not work properly if it is left for
a long period at a temperature above or below the
indicated range.
Temperature inside the compartments may be
influenced by various factors such as: position of the
appliance, ambient air temperature, frequency of
door opening.
Install the appliance in a dry and well-ventilated
place.
Avoid locations in direct sunlight or near a source of
heat (oven, heating, etc.). If this cannot be avoided,
install the appliance respecting the following
minimum distances:
Coal or paraffin stoves: 30 cm
Electric and/or gas stoves: 3 cm
Install and level the appliance on a floor strong
enough to take its weight and in an area suitable for
its size and use.
To allow product handling and sufficient air
circulation, leave at least 1 cm clearance at the
sides, above the appliance, and between the rear
panel and the wall.
Climatic class T. Amb. (°C) T. Amb. (°F)
SN From 10 to 32 From 50 to 90
N From 16 to 32 From 61 to 90
ST From 18 to 38 From 64 to 100
T From 18 to 43 From 64 to 110
63733123GB.fm Page 4 Tuesday, February 15, 2005 3:29 PM