background image

12

q

 

Check electrical requirements. Be sure that you have the 

correct electrical supply and the recommended grounding 

method. 

q

  

Check that all parts are now installed. If there is an extra part, 

go back through steps to see what was skipped.

COMPLETE INSTALLATION

q

  

Check that you have all of your tools.

q

  Check that shipping materials were completely removed  

from washer.

q

    

Dispose of/recycle all packaging materials.

q

    

Check that the water faucets are on.

q

    

Check for leaks around faucets and inlet hoses.

q

    

Remove film from console and any tape remaining on 

washer.

q

  Plug into a grounded outlet or connect power.

q  

Check that circuit breaker is not tripped or fuse is not blown.

 Start washer using the payment system (if available) to  

check that the wash cycle completes without an error code 

or water leak.

TYPICAL FULL LOAD SIZES

Load Type

Loading Suggestion

Load Type

Loading Suggestion

Mixed Load

3 double sheets

4 pillowcases

6 pair shorts

8 T-shirts

2 shirts

2 blouses

8 handkerchiefs

Heavy Work Clothes

3 pair pants

3 shirts

1 coverall

4 pair jeans

1 overall

Permanent Press

2 double or

1 king size sheet

1 tablecloth

1 dress

1 blouse

2 slacks

3 shirts

2 pillowcases

Knits

3 blouses

4 slacks

6 shirts

4 tops

4 dresses

Summary of Contents for CAE2765FQ0
















Reviews: