background image

17

Door filter, water container or bottom filter indicator lamp on:

Door filter clean?

Water container empty?

Water container correctly positioned?

Bottom filter clean and correctly positioned?

Water droplets underneath the dryer:

Bottom filter correctly positioned?

Any lint on the bottom filter seal removed?

Any lint on the door seal removed?

Water container positioned correctly?

Dryer levelled?

After-Sales Service
If, after carrying out the above checks the malfunction persists or appears again, turn the dryer 
off and call the After-Sales Service (refer to guarantee).

Please indicate:

The nature of the fault.

The dryer type and model.

The service code (the number after the word Service on the adhesive rating plate) on the lower side 
of the door opening.

Your full address and phone number.

Manufacturer:
Whirlpool Europe s.r.l.
Viale Guido Borghi 27
21025 Comerio (VA)
Italy

EC Declaration of Conformity

This dryer has been designed, constructed and distributed in compliance with the safety 
requirements of EC Directives:

2006/95/EC Low Voltage Directive.

2004/108/EC Electromagnetic Compatibility Directive.

www.devicemanuals.eu/

Summary of Contents for AZA9791



















Reviews: