5019 301 20162
Whirlpool is a registered trademark of Whirlpool USA.
The use of the prewash cycle increases programme duration by approximately 15 min. Consumption data was calculated
based on normalized conditions in compliance with Standard IEC 60 456. The data on the
Energy Label
refers to
programme
Coloured Cotton 60°C
. Consumption data in the home may vary with respect to the values in the table in
relation to the water supply pressure and temperature, the load and the type of wash. The drying times shown may vary
based on the spin speed and type of fabric.
Add the detergent as described in the programme
table or in the chapter
Detergent and Additives
in
the booklet.
1. Make sure that the
Programme selector
is set to
Stop
.
2. Open the water tap.
3. Set the
Programme Selector
to the desired
programme.
4. Set the
thermostat knob
to the desired
temperature.
5. Set the
spin selector knob
to the desired speed.
6.
Special options
can be selected, if required.
7. Check that the door is well closed and turn on the
washer-dryer by pressing the
ON/OFF
button. The indicator light comes on, indicating
that the washer-dryer is on.
Dryer half load
button
(depending on model)
Intensive Rinse
button
(depending on model)
• The quantity of water duration of the rinse cycle
are increased.
• This option is especially recommended in areas
with extremely soft water, for baby linen and
linen belonging to skin allergy sufferers.
Rinse and Hold
button
(depending on model)
only for synthetic and wool programmes
• The laundry remains in the final rinse water
without progressing to the final spin cycle to
avoid creasing and prevent colours from running.
• This option is particularly recommended for the
programmes
Synthetics
or
Delicate
.
• This function is particularly useful if you want to
postpone spinning to a later time or when you do
not wish to spin the clothes.
To terminate the
Rinse and Hold
option
(depending on the model)
synthetic and wool programmes only
• Press the Rinse and Hold button again; the load
will be spun according to the selected
programme.
If you do not wish to spin the clothes, turn the
programme selector knob to the Drain cycle, after
pressing the
No Spin
button.
Spin Speed Reduction
Button
Reduces or increases the spin speed from 1200 to 550.
CONSUMPTION DATA
Programme
Temperature
Selector
(
)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx.
Programme Duration
(hours:minutes)
1 - Cotton
90°
5.0
57
1.85
2:28
2 - Cotton
90°
5.0
50
1.07
2:08
3 - Cotton
60°
5.0
53
0.97
2:00
4 - Cotton
40°
5.0
53
0.60
1:55
5 - Synthetics
60°
2.5
60
0.83
1:15
6 - Synthetics
60°
2.5
60
0.42
1:00
7 - Wool
40°
1.0
61
0.32
0:48
ADD THE DETERGENT, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT THE DESIRED OPTIONS
The door locks automatically after the programme
start until the end of the programme. If the
programme selector is moved to the
Stop
position
or if the electricity supply is interrupted, then after
approximately two minutes the door is released. In
this case do not open the door: because hot water
could come out of the door.
To change a programme when a cycle has already
begun:
1. Switch off the appliance by pressing the
ON/OFF
button.
2. Select the new programme.
3. Start the programme by pressing the
ON/OFF
button.
To interrupt the selected programme and continue
it at a later time:
1. Press the
ON/OFF
button.
2. After the desired interval has passed, press the
ON/OFF
button again.
1. At the end of the programme the programme
selector moves to the
Stop
position.
2. To unload the machine wait for the door to
release (approx. 2 minutes).
3. Switch off the appliance, open the door and
unload the washing.
4. Close the water tap and leave the door ajar to
allow the drum to dry out.
1. Load the machine according to the maximum
drying load table.
The drying function can only be used for cotton
and synthetic programmes (not wool) and
starts when the knob reaches the programme
stop mark.
It is important that the laundry has been spun
and was washed with water.
2.
When the spin cycle is finished the programme
selector moves to
Stop
.
3. Select a drying time based on the type of fabric
(cotton/synthetic), amount of laundry and
desired final results (iron/cupboard dry), using
the
Drying Time
knob.
4. Press the
Dryer Half Load
button.
5. Turn on the water tap, check the drain hose,
use the
ON/OFF
button to turn on (the
indicator light goes on).
1. The sequential washing and drying function
can only be used for energy-saving and
synthetic programmes (not wool) and starts
when the knob reaches the programme stop
mark.
2. Load the washer-dryer (according to the max.
drying load table) and close the door
3. Select a drying time based on the type of fabric
(cotton/synthetic), amount of laundry and
desired final results (iron/cupboard dry), using
the
Drying Time
knob.
4. Press the
Dryer Half Load
button.
5. Set the
Washing Programme
knob to the
desired programme
6. Press the
ON/OFF
button to start the
drying cycle.
•
CLEANING THE FILTER
To ensure smooth operation of the pump,
check the filter regularly and clean it when
necessary.
DOOR LOCK
CHANGING THE SELECTED PROGRAMME
INTERRUPTING THE CURRENT PROGRAMME
AT THE END OF THE WASH PROGRAMME
SETTING THE DRYING CYCLE
SETTING THE WASHING/DRYING CYCLE IN
SEQUENCE
NOTES AND INDICATIONS FOR USE
3gb20162.fm5 Page 2 Friday, March 1, 2002 11:47 AM
