Whirlpool AWO46075 Page 4 Programme Chart Download

Page: 4 / 4

W10342098A

To reduce water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

Reference programme for Energy and Water Labelling, according to the IEC EN60456.

The actual running time can deviate from the values in the table, because it takes into account the operating conditions applicable at that time.

Close the door after adding the detergents.Turn the programme

seletor knob to the desired programme and temperature.The

indicator next to “Start/Pause”button is flashing.

•

An extra rinse is added and rinse cycle prolonged.

• This option is particularly suitable for areas with very

soft water, washing baby linen and people with allergies.

• The display shows

“End”

, along with an audible signal,

and the

“Door Open”

indication lights up.

• All the lights of the programme sequence indicators

are off.

1. Turn the programme selector to the

“Off / 0”

position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar, to allow the drum to dry.

1. Press the

“Start / Pause”

button to pause the

programme. The indication light flashes.

2. Select the new programme, the temperature, options

and the required spin speed.

3. Press the

“Start / Pause”

button again. The new

programme continues at the same position, where

the previous programme was interrupted. Do not add

detergent again.

The

“Reset”

button cancels a set programme before

the end of the cycle. To reset, press the

“Reset”

button

for at least 3 seconds. Water from the machine is then

drained out, before the door can be opened.

Press the selected option button once, the current value is

displayed on the display. By pressing the button repeatedly, the

display will display the values in sequence. By pressing the

button of the desired option, the respective indicator lights up.

When the combination of programme and additional options is

not possible, the indication lights switch off automatically.

Unsuitable combinations of options are deselected automatically.

• Suitiable for heavily solided loads(for example with sand and

dust) and the programme duration is prolonged for 18 minutes.

“Intensive Rinse” button:

Open the tap and press the

“Start / Pause”

button.

The indication lamp next to the

“Start / Pause”

button

lights up. The programme sequence indicator shows

the current programme phase, from left to right, as

Prewash, Wash, Rinse, Rinse Hold and Spin / Drain.

The time display shows the remaining programme

time. Due to variations in load and the temperature of

the inlet water, the remaining time is re-calculated in

certain programme phases. When this occurs, the

remaining programme time is replaced by an

animation.

Before the start and after the end of a programme, the

“Door Open”

indication lamp, lights to show that the

door can be opened. While a wash programme is

running, the door remains locked and must on no

account be forced open. In case, there is an urgent

need to open it during a running programme, press the

“Start / Pause”

button and then press the

“Reset”

button.
Refer to

“

CANCEL / RESET A RUNNING

PROGRAMME BEFORE THE END

”.

If the appliance has insufficient or no water supply, the

“Water Tap Closed”

indication will light up. Open the

water tap. If the indication still lights up, refer to the

“Trouble Shooting Guide”

in the Instructions for Use.

“Water Tap Closed”:

If the waste water is not being pumped out, the

“Clean

Pump”

indication will light up. Check whether the drain

hose or the filter requires to be cleaned. In the latter

case, refer to,

“Removing the Filter”

in the Instructions

for Use.

“Clean Pump”:

“Prewash” button:

PROGRAMME START

RED FAILURE INDICATIONS

CHANGE PROGRAMME AND / OR

OPTIONS AFTER PROGRAMME START

CANCEL / RESET A RUNNING

PROGRAMME BEFORE THE END

Programme

Temperature

(

Max.Load

(Kg)

Approx.Duration

(hours:minutes)

Cotton

7.5