5019 301 06367
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
1.
Turn the programme selector to the desired
programme and temperature.
2.
The time display shows the duration of the chosen
programme (in hours and minutes), and the “Start
(Pause)” indication lamp blinks.
3.
The indication lamp of the predefined spin speed lights up.
Push the button(s) of any option(s) desired - the respective
indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Clean+” button
• Choose this option if you use an in-wash additive for
stain removal (powder, for example “Vanish”) - it will
optimize the additive’s efficiency to get better wash
performance and stain removal.
• Selectable for programmes “Cotton” and “Synthetics”; choose
temperature of 30 or 40°C and use with maximum load.
• Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together
with your detergent (only use powder detergent with this
option). Respect the manufacturer’s dosing instructions.
• Prolongs the programme by approx. 10 to 15 minutes.
• Appropriate for use of stain removers and bleaches on
oxygen basis. Chlorine or perborate bleaches must
not be used!
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
• Do not use liquid detergent for the main wash when
activating the “Prewash” option.
“Easy ironing” button
• Reduces creasing by an increased water quantity and a
very gentle spin.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft
water, washing baby linen and helps people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and
prevent colours from changing.
• It is particularly useful if you want to postpone spinning
to a later time, or if you want to drain only.
• If you select “Rinse hold” do not leave the laundry
items to soak for too long.
Note: The programme stops to “Rinse hold” at the
time the “Rinse hold” light in the programme sequence
indication is on. The indication lamp next to the “Start
(Pause)” button blinks.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)*
Cotton
95
7.0
74**
2.10
2:10
Cotton
60
7.0
54
1.19
2:20
Cotton
40
7.0
69
0.75
2:05
60
7.0
69
0.84
4:00
Synthetics
60
3.0
46**
0.80
1:35
Synthetics
40
3.0
42
0.40
1:20
Delicates
30
1.5
60
0.50
0:45
Daily load
40
4.0
48
0.50
1:00
30
4.0
48
0.25
0:30
Wool
40
1.0
60
0.55
0:45
Handwash
40
1.0
45
0.55
0:40
Eco Cotton***
60
7.0
54
0.91
4:00
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary
with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
Terminate the “Rinse hold” option:
• Press the “Start (Pause)” button; the programme
will terminate automatically with the final spin cycle for
the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector to the “Drain” programme and
press the “Start (Pause)” button.
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only.
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating the “Start delay”.
• Select programme, temperature and options.
• Press the “Start delay” button to select the delay time
by 1 to 23 hours;
• Press the “Start (Pause)” button.
The countdown of the delay time begins; the “Start
delay” indication lamp and the dot on the display will
keep blinking until the programme starts.
• The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
• Once having pressed the “Start (Pause)” button, the
number of hours preselected can be reduced by
pressing again the “Start delay” button.
To cancel the “Start delay”
...before you press the “Start (Pause)” button:
• Turn the programme selector to another position or
press the “Reset” button.
...after having pressed the “Start (Pause)” button:
• Press the “Start (Pause)” button - the delay time
disappears from the display. Press “Start (Pause)” again
if you want to start the selected programme immediately.
Open the tap and press the “Start (Pause)” button. The
indication lamp of the “Start (Pause)” button lights up.
The programme sequence indicator shows the current
programme phase, running from left to right through
Wash, Rinsse, Spin/Drain.
The time display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the remaining
time is newly calculated in certain programme phases. If this is
the case, an animation appears on the time display.
Before starting and after end of a programme, the lamp
lights to show that the door can be opened. As long as a
wash programme is running, the door remains locked and
must on no account be forced open. In case you have an
urgent need to open it during a running programme, refer
to “Reset a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a
fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for Use; if
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap; if the indication still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain
hose is kinked or the filter must be cleaned; in the latter case
refer to the Instructions for Use (“Removing the Filter”).
•
All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1.
Turn the programme selector to the “Off/O” position.
2.
Close the water tap.
3.
Open the door and unload the machine.
4.
Leave the door ajar to allow the drum to dry.
1.
Press the “Start (Pause)” button to pause the
programme. The light blinks.
2.
Select the new programme (with temperature), any
options and another spin speed if you want.
3.
Press the “Start (Pause)” button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
The “Reset” button cancels a programme before the end.
•
Press the “Reset” button for at least 3 seconds;
“rES” appears on the display. The water is drained
out; it may last a while until you can open the door.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
30106367GB.fm Page 2 Friday, March 26, 2010 2:28 PM
Black process 45.0° 150.0 LPI