background image

5019 301 01107

Programme

Temperature

Selector

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton

95

6.0

59 *

1.90

2:00

   Cotton **

60

6.0

49

1.02

2:20

Cotton

40

5.0

56

0.70

2:00

Synthetics

60

2.5

50 *

0.80

1:35

Synthetics

40

2.5

46

0.50

1:20

Delicates

30

1.5

60

0.50

0:41

Quick wash

30

3.0

41

0.40

0:30

Wool

40

1.0

60

0.50

0:46

Handwash

40

1.0

45

0.50

0:41

Add detergents as indicated on the front page and 

as described in your Instructions for Use. 

Close the door and turn the 

programme selector

 

to the desired programme and temperature. 

The indication lamp next to the 

“Start/Pause”

 

button flashes.

CONSUMPTION DATA

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the 

home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type 

of wash.

*  To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

**  Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR AND 
SELECT THE PROGRAMME

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the 

lamp lights to show the the door can be opened. 

As long as a wash programme is running, the door 

remains locked and must on no account  be forced  

open. In case you have an urgent need to open 

it during a running programme, refer to “Cancel 

(Reset) a running programme before the end”.

RED INDICATIONS

“Service”

Lighting up of the “Service” indication can be 

caused by a fault in an electrical component. 

Refer to the “Troubleshooting Guide” in your 

“Instructions for Use”; if the fault persists, contact 

our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. 

Open the water tap: if the indications still lights 

up, refer to the “Troubleshooting Guide” in the 

Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether 

the drain hose is kinked or the filter must be 

cleaned: in the latter case refer to the Instructions 

for Use (“Removing the Filter”).

“Rinse hold” button

  The laundry remains in the last rinse water     

 

  without progressing to the final spin cycle to 

  avoid creasing and prevent colours from changing.

  This option is particularly recommended for 

  the programmes “Synthetics” and “Delicates”.

  It is particularly useful if you want to postpone

  spinning to a later time, or if you want to drain 

  only.

  If you select “Rinse hold” do not leave items to 

  soak for too long.

 

Note

: The programme stops to “Rinse hold” 

  at the time the “Rinse hold” light in the 

  programme sequence indication is on.  

  The indication lamp next to the 

“Start/Pause”

 

  button flashes.

Terminate the “Rinse hold” option:

  Press the 

“Start/Pause”

 button; the programme 

  will terminate automatically with the final spin 

  cycle for the present wash programme.

  If you do not wish to spin the clothes, turn the

  programme selector knob to the “Drain”

  programme and press the 

“Start/Pause”

     

 

  button

.

Whirlpool is a registered trademark of Whirlpool USA.

PROGRAMME START

Open the tap and press the 

“Start/Pause” 

button. The indication lamp next to the 

“Start/

Pause” 

button lights up. The programme 

sequence indicator shows the current programme 

phase, running from left to right through Wash, 

Rinse, Spin/Drain. When the programme phrase is 

finised, the corresponding indication goes out.

PROGRAMME END

  All the lights of the programme sequence 

  indicator are off, and the “Door open” indication 

  lights up.

1. Turn the programme selector to the “Off/O”

  position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

CHANGE PROGRAMME AND/OR OPTIONS 
AFTER PROGRAMME START

1. Press the 

“Start/Pause” 

button to pause the

  programme. The light flashes.

2. Select the new programme (with temperature), 

  any options and another spin speed if you want.

3. Press the 

“Start/Pause” 

button again. 

  The new programme continues at the same 

  position where the previous programme was 

  interrupted. Do not  add detergent for this 

  programme.

CANCEL (RESET) A RUNNING PROGRAMME 
BEFORE THE END

The 

“Reset”

 button cancels a programme before 

the end.

  Press the 

“Reset” 

button for at least 3 seconds.

  Any existing water is drained out before the 

  door can be opened.

SELECT ANY DESIRED OPTION

Push the button(s) of any option(s) desired - the 

respective indication lamp lights up.

When the combination of programme and 

additional option(s) is not possible, the indication 

lights switch off automatically. Unsuitable 

combinations of options are deselected 

automatically.

“Cold wash” button

  With this option, water is heated only up to 20ºC.

  Suitable for delicate laundry items with wash

  temperature recomendation of max. 30ºC on the

  care label.

 

Selectable only on the lowest temperature 

  step of each programme.

Reviews: