SELECT DESIRED FUNCTION
Press the desired option button and the corresponding indicator lights up.
When the combination of selected programme and the desired additional
option is not practicable, the option will be cancelled and the indicator
switches off immediately..
“Eco”
●
With a prolonged washing duration and lower washing temperature, a
desirable washing performance can be obtained and reduces energy
consumption.
“Prewash”
●
Suitable for heavily soiled loads (for example with sand and dust) and
the programme duration is prolonged for 15 minutes.
“Easy Ironing”
●
Can be used together with “Cotton”, “Synthetics” programmes to make
ironing easier.
●
To avoid creasing, water level is increased and gentle spin programme
is applied.
Performance Data
Programme
Cotton
※※
Cotton
※※※
Cotton
Cotton
Cotton
Synthetics
Synthetics
Daily Load 60 min
Daily Load 60 min
Quick Wash 30 min
Delicate
Wool
Wool
Handwash
Temperature
(°C)
95
60
40
30
Cold water
40
Cold water
40
Cold water
30
30
40
Cold water
Cold water
Load
(kg)
7.5
7.5
7.5
7.5
7.5
2.5
2.5
3.0
3.0
3.0
1.5
1.0
1.0
1.0
Programme Duration
(approximately) (hour:minute)
2:15
2:10
1:59
1:55
1:54
1:15
1:10
0:55
0:50
0:30
0:40
0:46
0:41
0:35
Performance data is measured in normal condition in compliance with IEC/EN60456 GB/T4288 standard. Energy and water consumption of domestic use is subject
to water pressure, temperature and the type of wash.
※
The actual programme time may deviate from the values in the table. The washing programme will be adjusted automatically according to the washing condition.
※※
To reduce the water temperature for preventing of wrinkles, cold water is added automatically after the main wash cycle and before draining process.
※※※
Standard Testing for Washing Programme
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME
Add the detergents as described in the “Detergents and softener” section
in the User Manual and close the door after adding detergents.
1. Turn the programme selector knob to the desired programme and
temperature.
2. The remaining time display shows the duration of the chosen
programme (in hours and minutes) and the indicator next to the
“Start / Pause” button is flashing.
3. The predefined spin speed indicator corresponding to the selected
programme lights up, display shows programme time.
“Intensive Rinse”
●
Adding one more rinsing programme and extend its rinsing duration.
●
This option is particularly suitable for areas with very soft water,
washing baby linen and helps people with allergies.
“Rinse Hold”
●
The laundry remains in the last rinse water without proceeding to
the spin cycle to avoid creasing and fading
●
This function is recommended for washing synthetic and delicate
clothes.
●
This function is very effective to delay the spinning time.
Note: When the “rinse-hold” light in the programme sequence is on and
the indicator next to “Start / Pause” button flashes, the programme
switches to rinse hold sequence and the programme stops.
How to stop the “Rinse Hold” Programme
●
Press the “Start / Pause” button, the washing machine
automatically switches to the spinning process of the selected
programme option, and the programme ends.
●
If you do not want to spin the clothes, please turn the programme
selector knob to the position of “Drain” programme and press the
“Start / Pause” button.
Variable Spin
●
Every programme has an automatic predifined maximum spin speed
●
Press button to select desired spin speed.
●
If the spin speed “0” is selected, the final spinning is cancelled.
Draining will occur when the programme ends, but spinning
continues during rinsing programme.
Start Delay Function
Start Delay Function allows running the machine at your convenience, for
example during night time when electricity is cheaper.
●
Select programme, temperature and additional function
●
Press the Start Delay button to select the delay time by 1 to 23 hours
●
Press the “Start / Pause” button, the indication light is on and the
machine starts the count down.
●
Start Delay indication light will go off when the programme starts, and
the remaining time is shown on the digital display
●
By pressing the “Start / Pause” button, and pressing the Start Delay
button again, the preset hours of the Start Delay can be adjusted.
Cancel the Start Delay function
●
Before pressing the “Start / Pause” button, turn the programme selector
knob to another programme position, or press the Reset button
●
After pressing the “Start / Pause” button, press and hold the Reset
button for 3 seconds, the Start Delay time will disappear from the
display.
Programme Start
Open the tap and press the “Start/Pause” button to start the wash
programme. The indicator next to the “Start/Pause” button lights up. The
programme sequence indicator will show the progress of the current
Prewash,wash programme. The sequence indication runs from left to
right to show Prewash, Wash, Rinse, Spin/Drain functions. The
Remaining Time Display will show the programme remaining time. With
the variations in the type of clothes and temperature of the inlet water, the
control will recount the remaining time at a certain stage when the
programme is running. At the same time, the display will show the
corresponding icons.
“Door Open” Indicator
Before the programme starts and after it ends, the indicator will light up
and the door of the machine can be opened. When the Programme is
running, the door will remain locked and cannot be forced open or the
machine will be damaged. If you need to open the door urgently during
the programme is running, please refer to the Chapter of “Cancel / Reset
A Running Programme Before It Ends”.
Red Indicator for Warning
Water tap closed
The appliance has no or insufficient water supply. Open the water tap; if
the indicator still lights up, refer to the “Troubleshooting Guide” in the
Instructions for Use.
Clean Pump
Waste water is not pumped out. Check whether the drain hose is kinked
or clogged. Clean the filter if it is the latter case. Please refer to the
chapter of “Removing the filter” in the Instructions for Use.
Programme Ends
●
All of the lights of the programme sequence are off. “Door Open”
indicatior lights up.
1. Turn the Programme selector to the “Off” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry out.
Change Programme and Options after the Programme Starts
1 Press the “Start/Pause” button to pause the Programme. The indicator
flashes.
2. Select the new programme and any additional function. Select the
spin speed if necessary.
3. Press the “Start/Pause” button again to start a new programme.
The new Programme continues at the same position where the
previous Programme was interrupted, so no additional detergent is
needed.
Cancel / Reset A Running Programme Before It Ends
Press the “Reset” button to cancel a programme before the programme
ends
●
Press the “Reset” button for at least 3 seconds. Any water that
remains in the appliance will be drained out before the door is opened.
Whirlpool is a registered trademark of Whirlpool USA
461970434021
