manualshive.com logo in svg

Whirlpool AKC7250 C/BLM, Instructions For Use Manual

Share
Download
Whirlpool AKC7250 C/BLM Instructions For Use Manual Download Page 18

 

 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This specification is subject to change without notice. FIAMMA TRADING SDN. BHD. will not be held responsible for the use of superseded or 
voided specifications. Fabricator must check for cut-out accuracy.   

 

 

FIAMMA TRADING SDN. BHD. (330476-P)                                                                             

Website: www.haustern.com     

Wisma Fiamma, No. 20 Jalan 7A/62A, Bandar Manjalara                                   

 

Office Number: +603-6279 8888 

52200 Kuala Lumpur, Malaysia. 

 

WARRANTY: 

 

 

  Standard 1-year warranty on manufacturing defects.   

PRODUCT WARRANTY REGISTRATION: 

 

 

Log on to www.haustern.com for product warranty registration and more information on the terms and 
conditions.   

 

Please refer to the serial number labeled on product body or carton box for warranty registration.   

Summary of Contents for AKC7250 C/BLM



















Reviews:

No comments

Brands by name

Popular brands

Load more brands