background image

12

WARNING! Installation must be carried out by 
a qualified electrician who is fully aware of 
current safety and installation regulations. The 
manufacturer declines all liability for injury to 
persons or animals and for damage to property 

resulting from failure to observe the regulations 
provided in this chapter.

Electrical connections

Hob electrical connection must be made before connecting 
the appliance to the electricity supply.

Electrical connection must be carried out in compliance 
with the regulations of the local electric utility company.

Make sure that the voltage indicated on the rating plate on 
the underside of the appliance corresponds to the domestic 
power supply voltage.

Regulations require that the appliance is earthed: use 
conductors (including the earth conductor) of the 
appropriate size only.

For electrical connection, use an H05 RR-F type cable as 
specified in the table “Power supply voltage”.

Connecting to the terminal board

Connect the yellow/green earth wire to the terminal with the 

symbol

. This wire must be longer than the other wires.

1.

Remove the terminal block cover (

A

), undoing the screw 

and inserting the cover in the terminal block hinge (

B

).

2.

Strip approx. 70 mm of sheath from the power supply 
cable. 

3.

Strip approx. 10 mm of sheath from the wires. Insert the 
power supply cable into the cable clamp and connect the 
wires to the terminal board as indicated in the diagram 
next to the terminal board itself.

4.

Secure the power cable with the cable clamp.

5.

Close the cover (

C

) and screw it on the terminal block 

with the removed screw - point (1).

Each time the cooktop is connected to the mains it 
carries out an automatic check which lasts several 
seconds.

WARNING! The power supply cable must be 
long enough to allow the hob to be removed 
from the worktop and must be positioned so as 
to avoid damage or overheating caused by 
contact with the base of the hob itself. Do not 

use extension leads.

Power supply voltage

If the hob already has a power cable, follow the 
instructions given on the label attached to the cable.
Connect the appliance to the electricity supply by 
means of an all-pole disconnect switch with minimum 

contact gap of 3 mm.

INSTALLATION and ELECTRICAL CONNECTION

DOMINO

Wires

Amount x size

230V ~ + 

3 X 4 mm

2

 

(3X2.5 mm

2

 Domino)

230-240V ~ + 

3 X 4 mm

2

 (Australia only) 

(3X2.5 mm

2

 Domino)

230V 3 ~ + 

4 X 1.5 mm

2

400V 3N ~ + 

5 X 1.5 mm

2

400V 2N ~ + 

4 x 1.5 mm

2

230V

230V

230V

230V

230V

230V

230V

230V

230V

230V

230V

A

B

C

400V 3N ~

230V ~

230-240V~FOR AU ONLY

230V~FOR UK ONLY

400V 2N ~

230V 3~

ONLY FOR BELGIUM

400V 2N~

FOR NL ONLY

77X35

31902052GB.fm  Page 12  Wednesday, September 3, 2008  4:05 PM

Summary of Contents for ACM 710/NE








Reviews: