Whirlpool 8572777 Installation Instructions Manual Download Page 7

7

Flexible metal vent must be fully extended and supported 
when the dryer is in its final position. 

Remove excess flexible metal vent to avoid sagging and 
kinking that may result in reduced airflow and poor 
performance.

Do not install flexible metal vent in enclosed walls, ceilings or 
floors.

Elbows

45° elbows provide better airflow than 90° elbows.

Clamps

Use clamps to seal all joints. 

Exhaust vent must not be connected or secured with screws 
or other fastening devices that extend into the interior of the 
duct. Do not use duct tape.

Exhaust

Recommended hood styles are shown here.

The angled hood style (shown here) is acceptable.

An exhaust hood should cap the vent to prevent rodents and 
insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground 
or any object that may be in the path of the exhaust (such as 
flowers, rocks or bushes, snow line, etc.).

Do not use an exhaust hood with a magnetic latch.

Remove Shipping Strap

To prevent floor damage, set washer/dryer onto cardboard before 
moving across floor. Move washer/dryer close to its final location.

1. Do not cut yellow strap. Pull yellow strap firmly, until 

completely removed from washer/dryer. There should be 
2 cotter pins on the end of the shipping strap. Remove the 
hang tag and pin from the vent pipe.

2. Tilt the washer/dryer forward. Move each of the 2 rear legs in 

an up-down motion to check the self-adjusting leveling legs 
for free movement. This is required for proper leveling. Gently 
lower the washer/dryer to the floor.

3. Cut the shipping strap about 16" (40.6 cm) from the plug end. 

Look for the words “CUT HERE.” Discard end with cotter pins. 
You will use the remaining piece of shipping strap to secure 
the drain hose.

           Good

        Better

Clamp

A. Louvered hood style
B. Box hood style

     4"
(10.2 cm)

      4"
(10.2 cm)

B

A

   4"

(10.2 cm)

2½"

(6.4 cm)

Improper venting can cause moisture and lint to collect 
indoors, which may result in:

Moisture damage to woodwork, furniture, paint, 

Housecleaning problems and health problems.

  wallpaper, carpets, etc.

WARNING

Excessive Weight Hazard

Use two or more people to move and install 
washer/dryer.

Failure to do so can result in back or other injury.

Summary of Contents for 8572777













Reviews: