background image

2

INSTALLATION INSTRUCTIONS

Tools and Parts

Gather the required tools and parts before starting installation. 
Read and follow the safety instructions provided with any tools 
listed here.

Tools needed:.

Parts supplied:

Remove parts package from the washer basket. Check that all 
parts were included.

WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.

Clear the room, building, or area of all occupants.

In the State of Massachusetts, the following installation instructions apply:

■  

Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by 

the State of Massachusetts.

■  

If using a ball valve, it shall be a T-handle type.

■  

A flexible gas connector, when used, must not exceed 3 feet.

8" or 10" adjustable 
wrench (for gas 
connections)

Flat-blade screwdriver

Adjustable wrench that 
opens to 1" (2.5 cm) or 

⁹⁄₁₆

" (14 mm) open-end 

wrench (for adjusting 
dryer feet)

Level

¼" nut driver or socket 
wrench

Wood block (for leveling)

Knife

Vent clamps

Pipe-joint compound 
resistant to L.P. gas

Caulking gun and 
compound (for installing 
new exhaust vent)

Pliers

Ruler or measuring tape

Tin snips (new vent 
installation)

A. Water inlet hoses (2)
B. Inlet hose flat washers (4)

C. Rear leveling legs (2)
D. Front leveling legs (2)

E. Plastic strap
F. Drain hose

G. Yellow, single wire hose clamp
H. Silver, double wire hose clamp

A

B

C

D

E

F

G

H

Summary of Contents for 8562591













Reviews: