background image

9

HOW TO FILL THE DETERGENT DISPENSER

Only use detergents recommended for use in domestic dishwashers.
Only fill the detergent dispenser prior to starting a wash 
programme 
(see the Quick Reference Guide).
1. Press button C to open the cover.
2. How to fill the detergent dispenser.

Programmes with pre-rinse:
-

Powder and/or liquid detergent: 
pour two thirds of the recommended dosage into the 
compartment (A);
pour one third into the compartment (B).

-

Tablets: 
place a tablet in the compartment (A) and/or follow the 
directions on the detergent pack.

Programmes without pre-rinse:
-

Powder and/or liquid detergent, tablets:
pour the entire recommended dosage into the compartment (A).

For programmes with additional “Half load/Multizone” function 
selected (if provided):
-

When using powder or liquid detergent the dosage can be 
reduced by 1/3.

3. Close the cover.

Detergent
Use good quality liquid or powder dishwasher detergents and/or 
tablets (do not use hand dishwashing detergents).
On some models the type of detergent used can be selected (D).

Selector on the inside of the door (on the left).
If, on the other hand, you are using a normal powder detergent, check 
the levels of regeneration salt and rinse aid, topping up as required.
In order to safeguard the environment, follow the manufacturer’s 
directions for use. Do not use more than the amount of detergent that 
is recommended. Observe the manufacturer’s safety warnings. 
Keep these products out of reach of children.
If you use detergents in tablet form, follow the manufacturer’s 
directions for use.
If you use multi-action dishwasher detergents that incorporate rinse 
aid and regeneration salt, follow the directions below:

• products that incorporate the rinse aid enhance the detergent 

action only with some programmes.

• products that make the use of regeneration salt unnecessary (3 

in 1 / 4 in 1) are only suitable for use with water up to hardness 
level 3. 
For water with a higher hardness level, regeneration salt must 
be added too.
To activate the salt level indicator, selcet position 2 in 1.

Read the product user instructions carefully. If in doubt, contact the 
detergent manufacturer.
The guarantee is not applicable if faults are caused by the use of these 
products.

A

B

C

• Position  E

-

for one component detergents: gel, tablets, 
powder;

• Position  F

-

for two component detergents (with rinse 
aid - 2 in 1);

• Position  G

-

for three or four component detergents 
(with rinse aid and salt - 3 in 1; 4 in 1).

39694178GB.fm  Page 9  Wednesday, September 27, 2006  11:11 AM

Black process 45.0° 150.0 LPI 

Summary of Contents for 7560/1










Reviews: