1
、
Electricity parameter
Rated voltage
Rated electric current
Reference circuit voltage
220VAC
2750W
<4A
12V
Rated power
2
、
Electric installation
2.1
2.2
2.3
2.4
power supply's establishment should be compled with nation security standard, voltage
and frequency also shoule be accord withproduct's nameplate.Especially install creep-
age protect switch and also check whether can connect with ground.
The wire collected to the massage bathtub should be fitting permanent., and the wire
should be a three-core wire, the sectional acreage of each core cannot less than 12A.
when wire pass the wall,it should be use bushing for protection until the AC outlet.
Ground wire of bathtub should be test whether works with house appliance ground wire.
The wire end of electricity control box should connect to the control panel, water bottom
light, loudspeaker, electrical engineering and the detector protection respectively.
3
、
Water supply device
3.1
This device's hydraulic pressure is 0.2-0.4Mpa.
3.2 The water supply characteristics on the wall: The cold or hot water supplies inside the
bathroom also establish in the shelter of the massage tub, use the hose to connect with
the cold or hot joint of the tub. the pipe towards is decide by the customer, the machine
do not go with the hose.
4.1
4.2
4.3
4.4
4.5
Before install, must consider the place of install massage bathtub whether can support
this device's pressure.
Place the massage bathtub on the install position, adjust level to make the drain system
smooth.
Adjust the leg's screw to make sure all of the screw touch ground completely.
Install the drain hose, and make some measure to against on the connecter.
Fix cold and hot water-pipe well, then install the showerhead. And then put drain into
downcomer, finally connect with power and make sure whether device connected with
ground can work.
5
、
Using Method
4
、
Installation introduction
5.1
5.2
5.3
Turn on faucet, adjust water's temperature, add water to the massage bathtub.when the
highest water level exceed the highest nozzle about 20-30mm and reach the detector,
press the switch button to let the electric machine.
Revolve the adjust switch ,and choose the proper surf pressure.
After finishing if should turn off pump at first, then open drain button,when water is all out ,
please make a clean of bathtub to keep in good.
Page
2
of
7
6
、
Clean and keep in good condition
.
.
6.1 usually use soft cloths and general liquid cleanser can wash away dirt , but forbid to use the
cleanser with acetone or the ammon ia comp osition;when disinfect, forbid to use the disinfector
contained the formal dehyde.
6.2 the dirty spot of surface can use the toothpaste to wipe with the soft cloth
6.3 to the low-grade chafe of the surface or burned by cigarette, can soak in water to whet with 2000#
levigation sand paper, then polishing.
6.4 If the electroplate piece contain stain, use the soft cloth to wipe lightly, avoid to wiping with coarse cloth
6.5 often clean up the backwater net cover, prevent it from stop;
Massage
bathtub
Massage
bathtub
Page
5
of
7
1
.Features(371)
：
1
、
Automatic testing water level by microcomputer.
2
、
Surfing function .
3
、
Bubble bath massage function .
4
、
External thermostat function
（
Configuration Options
）
5
、
Underwater light .
6
、
Ozone sterilization function
（
Configuration Opt ions
）
2.Specifications
：
1
、
：
AC190V--240V 50-60Hz
Power supply
5
、
：
1500V 1min
Dielectric strength
6
、
：
<0.25mA
Leak current
7
、
Lamp
：
AC12V 10W
8
、
Ozone
：
AC12V 8W
（
）
Configuration Options
4
、
：
AC220V 2W
（
）
Heater power
Configuration Options
9
、
：
IPX4
Waterproof grade
2
、
Water pump1 load
：
AC220V-240V 1500W
3
、
pump2 load
：
AC220V-240V 750W
Water
3.Install sketch
：
（
the configuration of installation should be accroding to
the selected model
）
12V10W
Lamp
Water pump
Water level sensor
Electric box
16A Plug
Heater
220V/2KW
Control panel
AC220V
INPUT
Ozone devi ce
AC12V /8W
O K
Water pump
