background image

1

Ultra Low Nox

Gas Water Heater

with the Flame Lock™ 

Safety System

Installation

Instructions and

Use & Care Guide

Do not store or use gasoline or other 
flammable vapors and liquids in the 
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
 

•  Do not try to light any appliance.

 

•  Do not touch any electrical switch;  

 

 

do not use any phone in your    

  building.
 

•  Immediately call your gas supplier  

 

 

from a neighbor’s phone. Follow  

 

 

the gas supplier’s instructions.

 

•  If you cannot reach your gas 

 

 

supplier, call the fire department.

Installation and service must be performed 
by a qualified installer, service agency or 
the gas supplier.

WARNING:  If the information in these

instructions is not followed exactly, a fire 

or explosion may result causing property 

damage, personal injury or death.

INSTALLER:
• 

AFFIX THESE INSTRUCTIONS TO OR ADJACENT   
TO THE WATER HEATER.

OWNER:
• 

RETAIN THESE INSTRUCTIONS AND WARRANTY 
FOR FUTURE REFERENCE. RETAIN THE ORIGINAL 
RECEIPT AS PROOF OF PURCHASE.

6510415

W10123251

March 2007

Table of Contents   ......................................................    2

®

To obtain technical, warranty, or service assistance during or after 
the installation of this water heater, visit our website at:

http://www.whirlpoolwaterheatersupport.com

or call toll free

1-877-817-6750

When calling for assistance, please have the following 
information ready:

1. Model 

number

2. 

7 digit product number

3. Serial 

number

4. 

Date of installation

5. 

Place of purchase

Summary of Contents for 201553






























Reviews: