Page 2
Specifications:
Input Voltage
.......................................................... 12.8 VDC +/- 20%
Standby Current
............................................................... 6 milliamps
Internal Fusing
....................................Integral fused 15A power input
Operating Temperature
.............................................. -30°C to +60°C
Storage Temperature
............................................... -40° C to +70° C
Aux Audio Input Specifications:
Square wave
.............................................. 0-6v signal (peak to peak)
Analog signal
.................................................... 0-0.9v (peak to peak)
Installation:
IMPORTANT! This product was designed as part of the
WeCanX™ system. It can not be used as a stand alone module.
Caution: Mounting will require drilling. It is absolutely necessary
to make sure that no other vehicle components could be
damaged in the process. Check both sides of the mounting
surface before starting. If damage is likely, select a different
mounting location.
WARNING! All customer supplied wires that connect to the positive terminal of the battery must be sized to supply at least 125% of the
maximum operating current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!
Mounting:
1.
Locate a suitable mounting location. A dry, cool compartment is a good choice.
2.
Position the unit on the proposed mounting location. Using an awl or similar tool, scribe the mounting surface where the mounting holes are to be
drilled. Make sure that this mounting area allows sufficient ventilation for the unit.
3.
Remove the unit and using a drill bit sized for a #8 sheet metal screw, drill a hole in each of the areas scribed in step 2.
4.
Return the unit to its mounting location. Using the supplied 8 X 3/4 sheet metal screws secure the unit onto the mounting surface.
5.
Wire and connect as shown above. Install a 15 amp fuse in the RED power wire.
Features
:
• 200 watt amplifier output.
• Configurable over CAN through any Cencom Core main box after adding it as a device in the command software.
• Each Amp out (+) and Amp Out (-) pair can supply up to 100watts of power to the siren speakers
• Auxiliary out (+) can be daisy chained to the next expansion siren or Howlers auxiliary in (+).
• Auxiliary out (-) can be daisy chained to the next expansion siren or Howlers auxiliary in (-).
• Auxiliary in (+) can be daisy chained from the previous Cencom Core expansion siren or Howlers auxiliary out (+).
• Auxiliary in (-) can be daisy chained from the previous Cencom Core expansion siren or Howlers auxiliary out (-).
• Reverse polarity protection up to 60V
• Over-voltage protection up to 60V
• Town and Country siren volume: The output power to the speakers can be switched between full volume (100 watts per speaker) and low
volume (10 watts per speaker). See programming software for operation.
• Short circuit protection
• Over-temperature protection
• Firmware upgradeable via main box
• Can be operated independently of other sirens
• Tones can be synchronized or asynchronous
• Internal memory to store larger siren files (4 MB)
• Low power mode
J2
J
1
M
A
I
N
FU
S
E
15
A
MP
O
UTPUT
S
2 - B
L
K
1
-
R
ED
4 - B
RN
-
Amp OUT (-)
5
- B
L
U -
Aux OUT (+)
6 - W
H
T/B
L
U
-
Aux OUT (-)
7 - G
RN
-
Aux IN (+)
3 - B
RN
-
Amp OUT (-)
2 -
Y
E
L
-
Amp OUT (+)
1
-
OR
G -
Amp OUT (+)
8 - W
H
T/G
RN
-
Aux IN (-)
C
O
MMU
N
IC
A
TI
ONS
C
A
B
L
E
2 -
SH
IE
L
D
3 - G
R
E
Y
- CAN L
1
- G
R
EE
N
- CAN H
S
I
R
E
N
P
O
WE
R
DI
A
G
NOS
TIC
L
ED
J3
J3
(+)
B
atter
y
(-)
C
AN
P
OR
T
2
4
3
2
1
8
3
7
2
6
1
5
1
J2
J
1
F
use
@
15 A
MP
S
