Page 2
Fig. 4
Fig. 3
5/16
Flat Washer
Slide U-Nut onto
Vehicle Support
Brace
5/16 - 18 X 1
Hex Head Bolt
wire passage
/drain hole
1/4 - 20 X 1-1/2"
HEX HEAD SS
1/4 X 20 X 1-1/4 HEX HEAD
SA315
1/4" SPLIT LOCK WASHER
1/4" SPLIT
LOCK
WASHER
Flexible
vehicle body
(Shown cut off)
Plastic cover / passengers side
Cut and
remove
Cut and
remove
Plastic cover / driver side
Cut and
remove
Cut and
remove
Plastic cover / passengers side
Cut and
remove
Plastic cover / driver side
Cut and
remove
Vehicle body
Vehicle body
Fig. 5
1/4" FLAT
WASHER
1/4" FLAT WASHER
Use hood latch hardware
Engine Compartment
Support
Brace
Support
Brace
Replace plastic rivets with supplied Hex Bolt
and U-Nut (2 places).
Fig. 2
Remove
plastic
rivets
Fig. 1
Remove plastic covers
Flexible front
of vehicle body
Disconnect
Hood latch
a s s e m b l y
Horn wire located here
Both front "ears" of the bracket
sit on brace on both sides of vehicle.
IMPORTANT: For drainage purposes, the speaker must be oriented so that the wire passage hole is in the “6 o’clock”
position (closest to the road).This is also the drain hole for the siren. Improper mounting will result in premature driver
failure and void the product warranty.
The SA315 siren speaker mounting kit comes with 3 long bolts (1/4-20 X 1-1/2” Hex Head).
The longer bolts are needed to go through the mounting bracket, the siren housing and
into the siren driver. They will replace 3 of the 4 shorter bolts (“A”) that now secure the
siren driver to the speaker housing. Your speaker is shipped with 2 of the shorter bolts
installed. A short bolt
be used in the hole that
go through the bracket so it
will properly secure the driver to the housing. If you need to remove all 4 bolts at once be
sure to hold the driver securely in place.
must
does not
wire
exit &
drain
hole
A
A
A
A
SA315 / Rear View
Loud siren noise
Can cause
Hearing loss.
Minimize exposure.
Close windows when using
CAUTION
Installation: 2005 Dodge Charger or Magnum
1.
Remove the 2 plastic covers that
protect the front area under the
hood (Fig. 1). They snap into or
out of the vehicle.
2.
Remove the 2 bolts that hold the
hood latch assembly on and set it
aside (do not disconnect the
cables). Unplug the horn wire and
place the wire out of the way (Figs.
1 & 2).
3.
Mount speaker to bracket (Fig. 3).
4.
Remove all the plastic rivets from
the top of the front of the body of
the vehicle, then pull the body
toward the front of the vehicle (the
body is flexible). Slide the 2 U-
Nuts onto the support braces (Fig.
4) and place the bracket (with
siren attached) on top of the U-
Nuts. The front “ears” of the
bracket rest on the two U-Nuts
which clip onto the support braces
(Fig. 4). The rear of the bracket will
mount behind the hood latch
assembly using the hood latch’s
mounting hardware (Fig. 2).
5.
Be sure all the hood latch cables
are properly located, then secure
the hood latch assembly over the
rear of the bracket using the hood
latch assemblies two bolts.
IMPORTANT: Make sure the two bolt heads line up with the two indentations on the hood latch assembly made by the bolts
original position, so that the hood latch assembly reinstalls in the same position and lines up properly with the hood.
6.
Reattach the horn wire then replace the plastic rivets you removed in step 5, except the 2 rivets that line up with the front mounting holes of the siren bracket.
Replace those rivets with the supplied mounting hardware (Fig. 4) securing the front of the bracket to the vehicle.
7.
First trim some plastic off of each of the two protective covers you removed in step 1 (Fig. 5) to accommodate the two ears on the front of the bracket, than snap the
two plastic covers back on.
8.
Extend WHITE (positive) and BLACK (negative) speaker wires to your siren amplifier and connect as shown in the amplifiers instructions.
Caution: It is the responsibility of the installation technician to make sure that the installation and operation of this product will not interfere with or
compromise the operation or efficiency of any vehicle equipment! Before returning the vehicle to active service, visually confirm the proper
operation of this product, as well as all vehicle components/equipment.
