Page 2
PART NUMBER
12
ITEM
11-381574-000
34-0041987-06
02-0363445-00
DESCRIPTION
HOUSING BASE
ROTATOR ASSEMBLY
50 WATT SNAP-IN HALOGEN LAMP
1
QTY.
13
14
2
8
9
10
11
7
6
5
4
3
1
68-4161381-V0
38-0241504-00
01-2861506-00
01-2861522-00
19-261465-000
68-4161381-50
68-4161381-40
68-4161381-30
68-4161381-20
68-4161381-10
15-101416-120
VIOLET LENS
#8 x 3/8” HEX WASHER HEAD S.M.S.
GASKET
MAGNETIC MOUNT KIT
MIRROR MOUNT KIT
CLAMP RING
RED LENS
GREEN LENS
CLEAR LENS
BLUE LENS
AMBER LENS
#10 X 3/4" PPHSMS TYPE A SCREW
A/R
1
A/R1
A/R1
1
4
1
1
A/R
A/R
A/R
A/R
A/R
1
WARNING:
All customer supplied wires that connect to the
positive (+) terminal of the battery must be sized to supply
at least 125% of the maximum operating current and fused
at the battery to carry that load.
14
0 1
1 2
3
4
5
6
78
9
10
11
12
DRILL OUT
MOUNTING
HOLES
DRILL WIRE
ACCESS HOLE
HERE
13
12
11
BLACK (-)
RED (+)
10
9
3 4
5 6
7 8
2
1
IMPORTANT
:
DO NOT INSTALL
BULBS EXCEEDING 50 WATTS.
In-line butt
connector
Grooved wire
to RED
Cigar Plug
& 6’ Cable
Magnet &
Mounting
Hardware
Smooth wire
to BLK
MOUNTING THE UNIT:
The RB6 Series uses a base that may be mounted one of two ways. It is designed to be mounted in a normal dome-up
position. If mounted in an inverted position, seal the wire exit hole and any mounting holes with silicone seal.
1” N.P.T. PIPE MOUNT:
1.
Feed the beacon wires through the pipe.
2.
Extend the RED beacon wire to +12VDC and fuse at 5 amps (see warning). Extend the BLACK beacon wire to
chassis ground (-).
This unit is polarity sensitive!
3.
Screw the strobe beacon onto the pipe, being careful not to pinch or strain the wires.
Hand tighten
the unit onto
pipe.
PERMANENT SURFACE MOUNT:
Note: It will be necessary to remove the dome in order to use this mounting style.
1.
Remove the clamp ring securing the dome to the base and remove the dome.
2.
Locate the 3 mounting hole indentations on the inside bottom of the base. Drill openings at these locations sized
to accomodate the sheet metal mounting screws (customer supplied). Deburr these openings and remove any
shavings.
3.
Using the base as a template, mark the location of the three mounting holes and wire access hole onto the
mounting surface.
4.
Using an appropriately sized drill bit (based on the mounting hardware used and the thickness of the mounting
surface), drill the three mounting holes marked in step 3. The wire access hole should be drilled using a 1/4” drill
bit. Deburr all holes and install a rubber grommet (customer supplied) to protect the wires.
5.
Feed the wires through the wire access hole in the mounting gasket, and the mounting surface.
6.
Align the mounting holes in the base, gasket, and mounting surface. Fasten with the three sheet metal screws.
7.
Extend the RED beacon wire to +12VDC and fuse at 5 amps (see warning). Extend the BLACK beacon wire to
chassis ground (-).
This unit is polarity sensitive!
8.
A magnet mount or mirror mount kit is available for purchase separately (see parts list).
