Page 5
NONE -
RFI Shield Drain
BLACK -
Ground/8 AWG
RED -
+12 VDC/8 AWG
GREEN -
BLUE -
GREEN-WHITE -
Front Outboard LEDs
BLUE-WHITE -
LEDs
-
Inboard LEDs
-
Front or Rear Inboard LEDs
VIOLET -
(See: Low Power Violet)
YELLOW -
WHITE -
WHITE-BLACK -
WHITE-ORANGE -
Cruise Lights
NONE -
WHITE-YELLOW - Not Used
WHITE-BROWN -
Front or Rear Inboard LEDs
WHITE-GREEN - Not Used
WHITE-BLUE -
Flashing Take-Down / Alley
WHITE-VIOLET - Scan-Lock™
WHITE-RED -
Front or Rear Inboard LEDs
the
T
In factory default configuration, this activates the
In factory default configuration, this activates the
In factory default configuration, this activates the
In factory default configuration, this activates the
This is the RFI shield drain wire and is connected to ground
In factory default configuration, this activates the
In factory default configuration, this activates the
In factory default configuration, this activates the
In the factory default configuration, this wire activates the
In factory default configuration, this wire activates the
In factory default configuration, this activates
In factory default configuration, this activates the
In factory default configuration, this activates the
In factory default configuration, this activates the
his will initiate low power operation of all LEDs
Front Corner LEDs
Rear Corner LEDs or Endcap
Front or Rear Outboard
GREEN-BLACK
Front
BLUE-BLACK
Passenger Alley Light
Driver Alley Light
Take-Down Lights
C
ontrol
C
able:
Ap12 VDC
to a control wire
will enable that
wires function.
The control cable
connects to your
control head or
switch box and
is fused there.
Typical fusing is
5 Amps
Fuse @ 40 Amp for fully loaded lightbar
GR
EE
N
B
LUE
GR
EE
N
-WHI
T
E
B
LUE-WHI
T
E
GR
EE
N
-
B
L
AC
K
B
LUE-
B
L
AC
K
YELL
O
W
WHI
T
E
WHI
T
E-
B
L
AC
K
VI
O
LE
T
WHI
T
E-
ORANG
E
WHI
T
E-
B
LUE
Front Corner LEDs
Rear Corner
Front or Rear Outboard
Front Inboard
Front or Rear In
Passenger Alley Light
Driver Alley Light
Take-Down Lights
Cruise Lights
LEDs or Endcap
Front Outboard LEDs
LEDs
LEDs
board LEDs
Low Power
Flashing Takedowns
POWER CABLE FUSING CHART
WI
R
E
CO
L
OR
FU
NCT
I
ON
3 amps
3 amps
3 amps
3 amps
3 amps
3 amps
0.5 amps
2.5 amps
2.5 amps
5 amps
5 amps
2.5 amps
A
MP
RAT
I
NG
CONTROL
CABLE
POWER
CABLE
Freedom
Lightbar
™
NFPA
All options may not be present on all Lightbars.
EXAMPLE:
If you are using the YELLOW, WHITE, & WHITE/ BROWN
function wires, the total amp draw is
ou
7.5 amps. Multiply this by 1.25
which comes out to 9.375 amps. Y
must fuse the RED power wire
at 10 amps.
Power Cable Fusing Chart:
After determining which function wires
you will use, add up the amp rating of each function wire. You must
then multiply this by 1.25 (see warning) and fuse the RED power wire
at this rating.
Wiring Designations:
The control wire functions shown below are given for a general reference only and may not match the
wire designations of your individual lightbar. For the wire functions of the specific lightbar you ordered, refer to the wiring
sheet attached to the instruction manual shipped with the lightbar.
