Page 2
1
4
2
3
1
4
2
3
(+)
Battery
(-)
Connect
negative terminal of
light to Ground
Connect
Positive terminal of light to
Output wire
15 AMPS EA
J4-1 - OUTPUT 1 - RED
J4-2 - OUTPUT 2 - WHT
J4-3 - OUTPUT 3 - BLU
J4-4 - OUTPUT 4 - GRN
Connect
to WeCanX
CANbus
Fuse each
wire @
40 AMPS
REAR VIEW
REAR VIEW
These communication
wires must be a twisted
pair / 7 twists per linear ft
RED
RED
J1
GREY - J1-2 CAN LOW
18A
WG
12A
WG
GRN - J3 - CAN HIGH
BLK/WHT - J1-1 - CAN SHIELD
BLK - J1-4 - GND
Wire Gauge Chart
WARNING! All customer supplied wires that
connect to the positive terminal of the battery
must be sized to supply at least 125% of the
maximum operating current and
at
FUSED
the battery to carry the load.
DO NOT USE CIRCUIT BREAKERS WITH THIS
PRODUCT!
WeCanX
POSITIVE
Outputs
J4
J2
J1
BATTERY INPUT
+VBAT / 40AMPS
MAX each
J4
J2
J1
The WeCanX™ High Current Remote Expansion Module
Operates at 10-30V and connects to the WeCanX™ bus to
communicate with CenCom Core™.
Specifications:
Input Voltage
. . . . . . . . . . . . . . . . . . . . . . . .
10 - 30 VDC
Input Current
. . . . . . . . . . . . . . . . . . . . . . .
60 amps max
Sleep Current
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 mA
Output Current
. . . . . . . . . . . . . . . .
15 amps per output
Communication Protocol
. . . . . . . . . . . . . . .
WeCanX
Operating Temperature
. . . . . . . . . . . . .
-
40C to +65C
IP Rating
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . .
IP67
Features:
• Programmable High/Low Power
• Four 15 amp high current outputs / high side
switched
• All outputs syncronizable with other WeCanX
system outputs
• Outputs support standard & DVI flash
patterns
• Short circuit and over-current protection
• Reverse polarity and over-voltage protection
Mounting:
Selecting a mounting location:
This module has been designed to be mounted
under the hood, in the trunk or in the passenger
compartment. Regardless of the location selected,
the following notes must be observed:
• The module should be mounted on a flat
surface. Be sure that this surface is not one that
either generates or is exposed to excessive heat during normal
operation of the vehicle.
• Do not select a location where the module will be
exposed to potential damage from any
unsecured or lose equipment in the
vehicle.
• The mounting area should be easily
accessible for wiring and service purposes.
Be sure that the backside of the proposed
mounting surface does not hide any wires, cables, fuel
lines, etc., that could be damaged by drilling mounting holes.
• When you find a suitable location secure the module using the supplied
mounting hardware.
Wiring & Operation:
• Wire the module as shown
in the wiring diagram.
Follow the wire gauge chart
for proper wire size when
extending the wires.
NOTE:
Add the supplied shrink
wrap tubing to the
connectors.
• Extend the WeCanX wires to
the CenCom Core™ Main
Box and connect them as
shown. Operation is
controlled by CenCom
Core™.
• Extend two 10 AWG wires to
the positive terminal of the
battery, connect there and
fuse as shown.
• Extend the four positive output wires to the positive terminals of the
lights you wish to operate and extend the negative terminal of each light
to battery ground. Operation is controlled by CenCom Core™.
