Page 2
Specifications:
Voltage:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.8VDC +/- 20%
Reverse polarity protection:
. . . . . . . . . . . . . . . . . . . . . . . . . . Up to 60V
Over-Voltage Protection:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Up to 60V
Features:
• 8 or 16 programmable 2.5 AMP Positive switched outputs
• 4 programmable digital inputs
• Short circuit protection
• Over-temperature protection
• Diagnostic current reporting
• Firmware upgradeable via main box
• Low power mode
• Cruise Mode
Mounting:
Selecting a mounting location:
The remote module has been designed to be mounted under the hood, in
the trunk or in the passenger compartment. Regardless of the location
selected, the following notes must be observed:
The module should be mounted on a flat surface. Be sure that this surface
is not one that either generates or is exposed to excessive heat during
normal operation of the vehicle.
Do not select a location where the module will be exposed to potential
damage from any unsecured or lose equipment in the vehicle.
The mounting area should be easily accessible for wiring and service
purposes. Be sure that the backside of the proposed mounting surface
does not hide any wires, cables, fuel lines, etc., that could be damaged by
drilling mounting holes.
When you find a suitable location secure the module using the supplied
mounting hardware.
5 Amps
10 Amps
18 AWG
16 AWG
14 AWG
15 Feet
7.5 Feet
24 Feet
12 Feet
39 Feet
19.5 Feet
Wire
Gauge
Current Draw
3 - RED
4 - RED
1 - RED
2 - RED
Connect
negative
terminal
of light to
Chassis
Ground
Fuse each
wire @
10 AMPS
J7
1 - GRN / CAN H
*
2 - BLK/WHT - SHIELD
3 - GRY / CAN L
*
4- PLUG (not used)
*
These communication wires
must be a twisted pair
*
(7 twists per linear foot)
*
7 - WHT/VIO (+) POS
8 - WHT/GRY (+) POS
3 - WHT/ORG (+) POS
4 - WHT/YEL (+) POS
6 - WHT/BLU (+) POS
5 - WHT/GRN (+) POS
1 - WHT/BRN (+) POS
2 - WHT/RED (+) POS
10 - BLK
GND (-)
9 - YEL
Input 4 POS (+)
4 - WHT/YEL
Input 4 GND (-)
5 - BLK
GND (-)
6 - BRN
Input 1 POS (+)
7 - RED
Input 2 POS (+)
3 - WHT/ORG
Input 3 GND (-)
2 - WHT/RED
Input 2 GND (-)
1 - WHT/BRN
Input 1 GND (-)
8 - ORG
Input 3 POS (+)
1
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
2
3
4
5
6
7
8
9
10
2
4
1
3
INPUTS
Connect to Positive terminal of light. Connect
Negative terminal of light to chassis ground.
(+)
Battery
(-)
1
2
3
4
POSITIV2
SWITCHING
POSITIV2
SWITCHING
POSITIVE
SWITCHING
7 - VIO (+) POS
8 - GRY (+) POS
3 - ORG (+) POS
4 - YEL (+) POS
6 - BLU (+) POS
5 - GRN (+) POS
1 - BRN (+) POS
2 - RED (+) POS
1.
Determine the amount of current being drawn through the wire.
Locate this number in the top row. If the current value is between
1.
adjacent values, use the higher number.
1.
2.
Follow this column down until the
length of the wire is shown. If the
2.
exact length is between adjacent
2.
values, use the higher number.
2.
The wire gauge shown for this row
2.
represents the minimum size wire
2.
that should be used.
2.
J6 (2.5A MAX per outlet)
1 - Output 9
2 - Output 10
3 - Output 11
4 - Output 12
5 - Output 13
6 - Output 14
7 - Output 15
8 - Output 16
J5 (2.5A MAX per outlet)
1 - Output 1
2 - Output 2
3 - Output 3
4 - Output 4
5 - Output 5
6 - Output 6
7 - Output 7
8 - Output 8
J7
J9
J5
J10
J6
3 - GRY / CAN L
1 - GRN / CAN H
4- PLUG
2 - BLK/WHT - SHIELD
