background image

CARE  OF  THE  LAWN  RA NGER 

1. 

Keep  the  Lawn  Ranger  greased  and  oiled  regularly. Refer  to 

to  Figure  I  for  the  location  of  grease  fittings.  Check  transmission 

and  engine  case  oil  levels. 

2. 

Keep  engine  air  cleaner  clean.  This  will  add  to  engine  life. 

3. 

Keep  tires  properly  inflated.  See  previous  instructions. 

4. 

Keep  the  Lawn  Ranger  covered  and  in  a  dry  place  when  not 

in  use .. 

5. 

Keep  grass  and  dirt  out  of  engine  cowling  as  these  will  stop 

the  flow  of  air  and  decrease  engine  life. 

6. 

BRAKE  ADJUSTMENT.  The  brake  band,  located  on  the  left  side 

of  the  transmission,  bra kes  the  transmission  and  in  turn  stops  the 

wheels.  Adjust  the  nut  on  the  bra ke  rod  so  that,  when  you  depress 
the  clutch  pedal  all  the  way  down.  the  band  tightens  around  the 
brake  drum.  just  as  the  idler  pulley  releases  the  belt.  Keep  brake 

band  and  drum  free  from  oil  and  dirt. 

7. 

Clutch.Brake  Pedal  Ad'justment.  The  clutch-brake  pedal  rod 

may  be  turned  in  or  out  to  adjust  the  pedal  to  operator's  desired 

position.  Remove  pin  from  rod  and  turn  rod  in  or  out  for adjustment. 

S. 

When  blades  become  dull,  remove  and  regrind. 

CAUTION: 

Sharpen  evenly  on  both  sides  so  blade  does  not  become  out  of 

balance. 

9. 

On  the  Model  BE ,check  battery  after  every 

40 

hours  of  use. 

If  the  mower  has  been  in  storage it may  be  necessary  to  recharge. 

10. 

Your  Lawn  Ranger  is  only  as  good  as  the  service  you  give  it. 

See  your  Wheel  Horse  Dealer  for  a  thorough  check-up  after  each 
season  of  use. 

1 1. 

When  replacing  belts  be  sure  to  purchase  them  from  your 

Wheel  Horse  Dealer,  as  these  belts  are  specifically  designed  for 
each  application. 

(NOTE:  Make  sure  all  pulleys 

are 

in  line.) 

Figure 

OPERATION 

With  proper  care  and  adjustment.  your  new  Wheel  Horse  Lawn 

Ranger  has  been  designed  to  give  many  years  of  satisfactory 

performance. 

Preparation  for  operation  and  operating  hints  listed  below  are 

recommended  for  all  mowers  and  approved  by  the  Outdoor  Power 

Institute  for  safe  operation  of  your  mower. 

1. 

Before  starting  operation,  clear  the  entire  lawn  area  of  all 

debris  that  could  catch  on  to  or  be  thrown  by  the  blades. 

2. 

When  you  mow  on  rough  terrain  or  in  high  grass  or  weeds.  the 

blade  should  be  set  at  the  highest  cutting  point.  In  tall  grass  or 

weeds.  a  second  cutting  may  be  made  to  bring  the  grass  down  to 
the  desired  height. 

3. 

Mowers  do  not  operate  as  well  in  wet  grass.  Wet  grass  has  a 

"'--' 

tendency  to  build  up  on  mower  housing  and  give  non-uniform  dis­

charge. 

4. 

Fill  gas  tank  outdoors.  Avoid  spilling  gasoline  and 

don't  fill  the 

tank 

while  engine  is  running  or  while  you  are  smoking. 

5. 

While  mowing.  give  undivided  attention  to the  job  at  hand,  keep 

the  cutting  path  in  area  of  operation' clear  of  all  persons,  particu­

larly  small  child reno 

6. 

Never  leave  motor  running  unattended.  Remove  key  when  not 

in  use  - children  could  get  hurt. 

7. 

Don't  overspeed  the  engine.  Excessive  cutting  speed  or  tamper· 

ing  with  the  governor  can 'be  dangerous. 

S. 

The  �ower  has  side  plates  which  may  be  removed  when  cutting 

heavy  grass  or  weeds.  The  sideplates  may  be  reinstalled  in  an  in­

verted  position,  as  shown  by  the  dotted  illustration,  thus  acting  as 
an  additional  foot  guard. 

EXTREME  CAUTION 

should  be  exercised 

when  the  sideplates  are  removed,  because  of  the  danger  of  flying 

debris. 

9. 

Exercise  special  care  when  mowing  around  objects  to  prevent 

the  blades  from  striking  them,  and  never  deliberately  mOw  over 

any  object. 

10. 

Stop  operation  when  another  person  approaches  - prohibit 

others  from  riding  with  you  on  your  riding  mower. 

1 1. 

Riding  mowers  can  be  tipped  to  either  back  or  side.  Exercise 

extreme  ca ution  when  mowing  on  slopes  or  inclines.  Engage  clutch 

slowly  and  smoothly.  Never  abuse  your  mower  by improper handling. 

12. 

Never  adjust  mower  or  tractor  until  engine  has  been  turned  off. 

13. 

If  your  Lawn  Ranger  is  to  be  used  for  purposes  other  than 

mowing,  latch  mOWer  clutch  in  disengaged  position,  stop  engine 
and  remove  mower  drive  belt  from  engine  pulley.  The  spring  wire 
belt  stop  may  be  deflected  to  remove  belt.  Never  allow  children 

to  operate  unless  you  have  removed  this  belt  to  prevent  their 

accidentally  engaging  mower. 

(NOTE:  Auxiliary  Foot  Rest  for  use  only  when  mower  Is  removed. 

This  foot  rest  CAN  NOT 

be 

used  when  mowing.) 

BRAKE 

WHEEL  HORSE  LAWN  RA NGER  SPECIFIC A TIONS 

(SPECIfICATIONS  SUBJlfCT  T O   CHANGIf  WITHOUT  NOTICIf! 

Length  Overall 

. . . . . . . . . • • . . . .  

,. .... . . . . . .. . . . . . .   . . . . .   54 

inches 

Wheelbase 

. . . . . . . . . . . . . . . . . . . .  0 0 0 . 0 0 0 0 0 0  

• • • • • • • • • • • •  

41X 

inches 

Width  Overall  (with  mower)  .. ......

• •  

• • •  

0  0 

• • • • •  

o. 

33)1 

inches 

Width  Overall  (without  mower) 

• • • • •  

', 

0  0  0 

•  •  •  •  •  •  •  •  •  •  • •  

26% 

inches 

Width  at  Front  Wheels, 

. . . . .  0  0 

• • • • • • • • • • • • • • • • • • • • • • •  

24% 

inches 

Height 

• • • • • • • • • • •  ,  • •  

0  0 

• • • • • •  

• • • • • • • • • •  

• 

0  0 

• • • • • • • •  

33)1 

inches 

Height  to  Top  of  Hood 

• • • • • • • • • • • • • • • • • • • • • • • •  

• • • • •  

28% 

inches 

Net  Weight 

(33E) 

• • • • • • •  

• • • • • • • • • • •  

• • • • • • • •  

• 

• • • •  

365 

Ibs. 

Nef  Weight 

(33R) 

.

. . .. 

0  0 

• 

• •  

• • •  

0  0 

• • • • • • • •  

0  0 

• • • • • •  

0  0  • 

•  • •  

339 

Ibs. 

Frame  Clearance  .

• •  '  • • • • • • • • • • • • • • • • •  

• • • • • • • • • • • • •  

10% 

inches 

Engine 

(4 

cycle,  single  cylinder,  air  cooled) 

.

.

.

......

.

• • • • • •  

HoP. 

Fuel  Capacity 

• • • • • • • • • • • • • • • • • • • •  

0  • •  

• • •  

• • •  

• • • •  

,  0 

• •  

quarts 

Tires  (front) 

...........

.

.....

..

3.50 

Pneumatic 

(10" 

wheel  d'a.) 

Tires  (rear) 

.......

.

...

.

.....

• •  

4 .00 

8  Pneumatic 

(16" 

wheel  dia.) 

www.MyWheelHorse.com

Summary of Contents for Ranger 33R









Reviews: