Wharfedale Pro R1604 Operating Manual Download Page 14

R1604 & R2004

R Series Mixers

.13.

Maximum Output Level

+22dB(MIX L/ R, ALT 3~4)@600 ohm

(0.5% T.H.D at 1kHz)

+22dB(AUX SEND1~2) @600 ohm
+22dB(INSERT) @40 k ohm
+22dB(CTRL RO O M) @600 ohm
Over 100mW(Headphone) @40 ohm

Total Harmonic Distortion

0.0025% @+14dB 20Hz~20kHz
(MIX L/ R, ALT 3-4, AUX SEND1~2, CTRL ROOM) @600 ohm

Frequency Response

20Hz~ 20kHz, +0/ -1dB
(MIX L/ R, ALT 3-4, AUX SEND1~2, CTRL ROOM) @600 ohm

Hum and Noise

-127dB equivalent input noise

(Average, Rs=150 )

- 95dB residual noise(MIX L/ R, ALT 3-4, AUX SEND1~2, CTRL ROOM)
-90dB(MIX L/ R, ALT 3-4, AUX SEND1~2, CTRL ROOM)
* Master fader at nominal level and all channel assign switch OFF.

Maximum Voltage Gain

72dB MIC IN TO MIX L/ R, ALT3~4
72dB MIC IN TO AUX 1
72dB MIC IN TO AUX 2(POST), EFX
74dB MIC IN TO CONTROL ROO M L/ R
72dB MIC IN TO REC L/ R
54dB LINE IN TO MIX L/ R, ALT3~4
58dB LINE IN TO AUX 1
58dB LINE IN TO AUX 2(POST),
60dB LINE IN TO CONTROL ROOM L/ R
22dB ST IN TO MIX L/ R, ALT3~4
20dB AUX RETURN IN TO MIX L/ R
16dB TAPE IN TO MIX L/ R

Maximum Levels

Mic in: +4dBu
Tape in: +13dBu
All other inputs: +25dBu

Interference(Crosstalk) at 1kHz

Main fader down: -85dBu 
Channel Alt/Mute switch engaged: -80dBu 
Channel fader down: -70dBu

Mono input channel gain

50dB variable(-60dB ~ -10dB), (-40dB ~ +10dB)

Input channel EQ (R1604)

HIGH: (+/-15dB) 12kHz shelving
MID: (+/-15dB) 2.5kHz shelving
LOW: (+/-15dB) 80Hz shelving
* Turnover/ rollover frequency: located 3dB below the point of maximum 
amplification and attenuation

Input channel EQ (R2004)

HIGH: (+/-15dB) 12kHz shelving
MID: (+/-15dB) 100~8kHz(EQ for frequency variable) peaking
LOW: (+/-15dB) 80Hz shelving
* Turnover/ rollover frequency: located 3dB below the point of maximum 
amplification and attenuation

Level meter

10- Segment LED X 2(output of +4dB at 0dB)
Main L/R

Peak indicator

Input channel: turns on 3dB under pre-fader signal clip

Phantom power

+48V DC

Power/ power consumption

R1604/ 2004: AC 100V/ 120V/ 230V/ 240V, 50/ 60Hz

Weights

R1604: 5.9kg, R2004: 7.3kg

Dimensions(mm)

R1604: 80.3 x 225 x 280
R2004: 80.3 x 416 x 431

SPECIFICATIONS - R1604/R2004

*0dB=0.775Vrms, 0dBV=1Vrms

Summary of Contents for R1604

















Reviews: