background image

www.whammerdyne.com

INTRODUCTION

Congratulations on buying the Truth

 amplifier, which combines the beautiful tonality of a zero-

feedback, direct-heated 2A3 triode with the speed, presence and immediacy of an ultra-wideband 
amplifier (6 Hz to 140 kHz). The Truth

 amplifier has a wider bandwidth than any analog source, 

and any digital through 196/24. Part of the reason for the extraordinary bandwidth is the complete 
absence of coupling capacitors and cathode-bypass capacitors in the Truth

 circuit.

All tubes operate in fixed-bias mode, with very low source impedances in the cathode circuit, and 
they are connected by the innovative Z-Direct Interface

©

, which has zero phase shift, does not store 

energy, and provides instant recovery from clipping. It’s a difference you can hear and enjoy for the 
life of the amplifier. Speaking of life, the Truth

 has a precision bias circuit that lets you optimize all of 

the tubes for optimum sound and the longest possible life.

Although the Truth

 amplifier is ready to plug-and-play, thanks to the extended burn-in and testing 

at the factory, there’s an optional bias setting procedure that lets you dial-in the bias to any good 
working set of 6DJ8 and 2A3 tubes. Do you have a personal favorite set of 6DJ8’s and 2A3’s? Bring 
‘em on! The multifunction bias meter, unlike a TV-type tube tester, measures the tubes in-circuit, at 
the actual voltages and currents of the working circuit, so you can be confident all tubes are operating 
at the exact optimum parameters.

We’ve poured our dedication, love of music, and decades of engineering talent into this amplifier.  
Welcome to the Truth

!

Whammerdyne  Team

        

 

 

 

Summary of Contents for Truth

















Reviews: