Whale InstantMatch SDS236T Quick Connect Manual Download Page 2

Important Information

Please read the following information before setting up a 

Bluetooth

®

wireless technology connection 

between the Whale Instant Match

®

transformer and Mira

®

Advance Flex Extra (J09N) shower:

• The electrical wiring must conform to EU wiring regulations BS7671:2008 Part 7 (17th Edition).

• The Bluetooth

®

function of the Whale Instant Match

®

transformer will 

only work

with the Mira

®

Advance Flex Extra (J09N) shower. 

• Previous Whale Instant Match

®

Wireless transformers 

cannot be

connected wirelessly to the Bluetooth

®

wireless technology enabled Mira Advance Flex Extra Shower (J09N).

• Bluetooth

® 

wireless technology enabled transformers can be easily identified by the blue test button.

• For optimum signal strength, mount the transformer within 5 metres of the shower.

• Locating the transformer outside of a 5 metre radius may cause a communication breakdown between

the transformer and shower, resulting in intermittent or complete failure to operate.

• Be aware that in very rare situations, dense building material, metallic objects such as steel baths and

foil lined plaster board, or electronic devices may interfere with the Bluetooth

® 

wireless technology signal 

and result in intermittent failure. In this situation you should relocate the transformer closer to the shower.

• A hardwired connection must be established if a Bluetooth

® 

wireless technology connection cannot be 

made between the shower and transformer.

• If any component or cord is damaged, it must be replaced by a qualified person to avoid a hazard.

Set Up

1. Shower settings

• Before beginning the Bluetooth

® 

wireless technology

registration process, please ensure that the “Pump LK2” 
switch inside the Mira

®

Advance Flex Extra (J09N) has

been set to the “ON” position, and that the "Pump LK1"
and "Pump LK3" switches remain in 
the "OFF" position as per the diagram shown.

• At this stage please ensure that your transformer is 
set to be used with Bluetooth

® 

wireless technology: 

the flow sensor setting must be set to 7 for “Bluetooth”
and the pipe inlet diameter must be set to 1 for 15mm.

1
2
3
4
5
6
7
8

BEAB

OFF

ON

43 DEG C

45 DEG C

RESERVED

6L/MIN

PUMP LK3

PUMP LK2

PUMP LK1

WARNING

Plumbing of the Waste Pipe

Bluetooth

®

wireless technology

A wireless Bluetooth connection may be used to allow the SDS236T

(755.678) Whale Instant Match

®

transformer to communicate with the

Mira Advance Flex Extra (J09N) shower without the use of a physical 

hardwired connection or external flow sensor to activate the pump.  

To set up the wireless connection, please follow the process below.

Whale 
Transformer
Settings

Blue Jumper - Sensor Position 7
Grey Jumper - Over run 10 Seconds
Red Jumper - Pipe inlet 15mm

BLUETOOTH MINI A5 (2018):Layout 1  27/03/2018  14:57  Page 3

Summary of Contents for InstantMatch SDS236T













Reviews: