background image

5

Short-Circuit Protection

Should a short-circuit occur in the RV, the WF-8700 Series Power Center converter will 

drop the voltage output to zero volts. If the short-circuit condition is removed and no 

other fault conditions are detected, the converter will resume normal operation. However, 

short-circuit conditions are dangerous, and an RV will require inspection by a qualified 

service technician.

CIRCUIT PROTECTION
WF-8700 Series Power Center Fuses and Breakers

DC Fuses (12 Volts)

The DC fuse boards have spaces the Branch, Battery and Reverse Polarity fuses as 

described above. Should any of fuses blow, the Branch Circuit fuses and the Reverse 

Battery Protection fuses should be replaced with ATC or ATO automotive type fuses such 

as:
• 

Littelfuse type 257

• 

Bussmann type ATC

AC Circuit Breakers (120/240 Volts)

The AC Breaker side of the WF-8700 Series Power Center is located on the left side of the 

enclosure. The WF-8700 Series Power Center accepts standard residential breakers. The 

WF-8712P and WF-8725P have spaces for a 30 Amp Main and up to 3 Branch breakers 

when using duplex breakers. The WF-8735P and WF-8740P have spaces for a 30 Amp 

Main and up to 5 Branch breakers when using duplex breakers. A list of factory tested and 

approved breakers follows. The breakers may be purchased at most big-box department 

stores and home centers.

 

UL-Listed Main Circuit Breakers, Rated for 120V, Maximum 30A

The following breakers have been factory tested and approved for use as 30 Amp Main 

breakers in the WF-8700 Series Power Center:

Manufacturer

Model/Cat. No./Type

Cutler Hammer

Type BR and C

Thomas Betts

Type TB or TBBD

ITE/Siemens

Type QP or QT

Square D

Type HOM or HOMT

Murray

Type MP-T or MH-T

General Electric

Type THQL

UL-Listed Branch Circuit Breakers, Rated for 120V, Maximum 20A

The following breakers have been factory tested and approved for use as Branch breakers 

in the WF-8700 Series Power Center:

Summary of Contents for WF-8700 Series

















Reviews: