Westport WEST ADR 80/02 User Manual Download Page 87

Page: 87 / 91

10.4. SCAL DOWNLOAD

Figure 10.4: SCAL wppAcknowledge Error

SCAL: Tx S-record: [xxxxxxxx] failed!

During SCAL download, the following error appears: “Tx S-record: [xxxxxxxx]
failed!” (Fig. 10.5)

Figure 10.5: SCAL S-record Fail

a. Re-download SCAL. See section “Basic SCAL Problems”

SCAL: No CAN Communication

During SCAL download, the following error appears: “No CAN Communication,
Please RESET Communication!” (Fig. 10.6)

Figure 10.6: SCAL no CAN error

a. There is a communication problem, to fix it see

Section 10.3 - General

Connection Problems

During SCAL: WEST Crashes

During SCAL download, WEST crashes.

a. Check that all cables and connectors are secure and restart computer.

b. Start WEST and try to download SCAL again.

WEST User Manual

Summary of Contents for WEST ADR 80/02




























































































Search results

Summary of Contents for WEST ADR 80/02

Reviews:

Related manuals for WEST ADR 80/02

Brands by name

Popular brands

Westport WEST ADR 80/02, User Manual

Search results

Summary of Contents for WEST ADR 80/02

Reviews:

Related manuals for WEST ADR 80/02

Brands by name

Popular brands