3
ENGLISH INSTRUCTIONS
1.
DO NOT
use the
Grinder
without the
Tray
secured into place.
2.
ALWAYS DISCONNECT Grinder
from
power source before servicing, changing
accessories or cleaning the unit.
3. Plug the
Grinder
into a standard 120 Volt,
60 Hz wall outlet.
4.
DO NOT USE
the
Grinder
if the
Power
Cord, Plug
or any other parts are damaged.
If the
Power Cord
or the
Grinder
is
damaged, call Customer Service.
DO NOT
ATTEMPT TO REPLACE THE CORD.
Be
sure to not allow the
Power Cord
to drape
into your work area. Check that all parts are
operating properly, and perform the intended
functions. Check for alignment of moving
parts or any other conditions that may affect
the operation.
5.
NEVER
use any accessories or parts from
other manufacturers. Doing so will VOID
YOUR WARRANTY and may cause fire,
electrical shock or injury.
6. TO PROTECT AGAINST RISK
OF ELECTRICAL SHOCK:
DO NOT
SUBMERGE THE
MAIN GRINDER BODY
INTO WATER OR LIQUID. BE SURE THE
GRINDER
IS DISCONNECTED FROM THE
POWER SOURCE BEFORE CLEANING.
Wash all parts by hand and thoroughly dry.
Thoroughly clean all parts that will come in
contact with food before using the appliance.
NEVER
rinse appliance
Grinder Motor
under tap, only use a moist cloth to clean the
Grinder Motor Unit
.
7. Reduce risk of unintentional starting.
Make sure the
Power Switch
is in the
“OFF” position before attaching to the power
source.
8.
KEEP FINGERS CLEAR
of the
Auger
and
Cutting Blades
AT ALL
TIMES
.
NEVER REACH INTO THE
GRINDER
, doing so may cause serious
injury.
ALWAYS USE THE PROVIDED
STOMPER, NEVER FEED FOOD BY
HAND.
GENERAL SAFETY RULES
READ AND FULLY UNDERSTAND ALL INSTRUCTIONS AND WARNINGS
PRIOR TO USING THIS UNIT. YOUR SAFETY IS MOST IMPORTANT!
FAILURE TO COMPLY WITH PROCEDURES AND SAFE GUARDS MAY
RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE. REMEMBER:
YOUR PERSONAL SAFETY IS YOUR RESPONSIBILITY!
9.
NEVER
use fingers to scrape food away
from the
Grinding Plate
while the
Grinder
is in
operation.
SEVERE INJURY MAY RESULT.
10.
NEVER LEAVE THE GRINDER
UNATTENDED.
Be safe,
DISCONNECT
the
Grinder
from power source before leaving the
work area. Close supervision is necessary
when any appliance is used near children. This
appliance is
NOT
to be used by children.
11. Wait until all moving parts have stopped
before you remove any part of the
Grinder
, or
before switching the
Grinder
in reverse.
12.
TIE BACK
loose hair and clothing, and roll
up long sleeves before operating the Grinder.
REMOVE
ties, rings, watches, bracelets, or other
jewelry before operating the
Grinder
.
13. Be sure the
Grinder
is on a stable work
surface. Be sure all the
Grinder Feet
are stable.
14.
DO NOT
attempt to grind bones or other hard
items.
15.
DO NOT
run
Grinder
without meat in the
Head
. Severe damage to the
Head
and
Auger
may occur.
16.
WEAR EYE PROTECTION.
Wear safety
glasses. Everyday eye glasses are not safety
glasses. Safety glasses conform to ANSI Z87.1
requirements. Note: approved safety glasses
have Z87 printed or stamped on them.
17.
DO NOT
use outdoors.
18.
DO NOT
use the
Grinder
while under the
influence of drugs, medications or alcohol.
19.
DO NOT
let the
Power Cord
hang over edge
of work surface.
20.
DO NOT
attempt to operate the
Grinder
if the
Grinder
itself is cold. The
Grinder
temperature should be at least 45
o
F (7
o
C) before
beginning.
21. The
Gear Housing
and the
Motor Cover
may
become HOT during operation. This is normal.
DO NOT touch these parts during operation or
until they cool after use.
SAVE THESE INSTRUCTIONS