manualshive.com logo in svg

Westinghouse WLE522WA, User Manual

Share
Download
Westinghouse WLE522WA User Manual Download Page 25

25

INSTALLATION

INSTALLATION

INSTALLATION

GAS TYPE

NATURAL GAS

UNIVERSAL LPG

PROPANE

Supply pressure at inlet to appliance regulator

(if fitted)

1.13 (kPa)

Minimum

2.75* (kPa)

2.75* (kPa)

Operate pressure at  

appliance test point

1.00 (kPa)

2.75 (kPa)

2.75 (kPa)

* If the regulator is placed upstream of the cooker inlet, as is normal for cookers operating on LPG, then the supply pressure and operating pressure are the same.
The following table shows the injector sizes for each burner.

INJECTOR

NATURAL GAS

UNIVERSAL LPG

PROPANE

Low heat burner

1.00 mm

0.55 mm

0.62 mm

Medium heat burner

1.35 mm

0.70 mm

0.82 mm

High heat burner

1.60 mm

0.90 mm

0.95 mm

Intense heat wok burner

1.75 mm

1.00 mm

1.00 mm

Grill – main injector

1.50 mm

0.82 mm

0.82 mm

Oven – main injector

1.60 mm

0.82 mm

0.95 mm

Oven – bypass screw

0.73 mm

0.45 mm

0.45 mm

CHECKING PIPE SIZE

To work out a suitable pipe size for connection use the information in this table.

NATURAL GAS

UNIVERSAL LPG

PROPANE

Configuration

STD  

Hob

WOK 

Hob

Electric grill 

in oven

STD  

Hob

WOK  

Hob

Electric grill 

in oven

STD  

Hob

WOK  

Hob

Electric grill 

in oven

Hourly gas  

consumption for cooker 58.7MJ

60.4MJ

47.6MJ

45.9MJ

49.2MJ

36.9MJ

56.5MJ

58.3MJ

47.5MJ

Also use information about the length of the run, number of 

elbows, tees and bends, the available service pressure and  

the supply requirements. AS/NZS 5601.1 will help you with 

this matter.

OPERATION ON NG

•   The appliance regulator MUST be orientated so that the 

pressure nipple is accessible.

•    The arrow showing the direction of flow MUST be  

pointed correctly.

•    The regulator has a ½” BSP internal thread at the inlet  

and outlet.

INSTALLATION

GAS REQUIREMENTS

This appliance must be installed by an authorised person, 

according to all codes and regulations of:
•    AS/NZS 5601.1 (particular attention to clause 6.10.1  

and figure 6.3 on page 97, and clause 6.10.1.11)

•    Local gas fitting regulations, municipal building codes  

and other statutory regulations.

UNPACKING

When packaging is removed from product you will notice there 

are several items nested in the packaging base.
The burner crowns, burner caps and trivets can be fitted to the hob.

The regulator or test point fitting installation is described in the 

front of the manual with UNPACKING.
The cookers come in three gas types: 

Natural gas, Propane and Universal LPG. If the cooker is 

required to use ULPG, a conversion kit can be obtained by 

contacting the Customer Care Centre for details. Before 

installation, check that the cooker is suitable for the gas supply 

by looking at the data plate behind the bottom of the oven door.
The following table shows the supply and operating pressures for 

various supplies.

Restraining Device

Anchor Points

Connection

Gas

Point

150mm

650mm

NG Regulator

Gas flow

Pressure test point

1/2" BSP

Internal thread

Summary of Contents for WLE522WA

































Reviews:

No comments

Brands by name

Popular brands

Load more brands