manualshive.com logo in svg

Westinghouse WGen12000, User Manual

Share
Download
Westinghouse WGen12000 User Manual Download Page 19

Westinghouse Outdoor Power Equipment | 19

STOPPING THE GENERATOR

Normal Operation

During normal operation, use the following steps to 

stop your generator:
1.  Remove any connected loads from the control 

panel receptacles.

2.  Allow the generator to run at “no load” to reduce 

and stabilize engine and alternator temperatures.

3. 

Position the engine control switch to 

STOP 

(see 

figure 10).

NOTE If you plan to store the generator after 

use, turn the fuel shutoff valve to the OFF 

position and allow the fuel to be consumed from 

the carburetor. 

4.  To stop generator remotely hold the 

OFF

 button on 

the wireless control (see figure 11). The generator 

may run for an additional 5 seconds as it goes 

through a cool down cycle before shutting off.

5.  Turn the fuel shutoff valve to the 

OFF

 position.

During an Emergency

If there is an emergency and the generator must be 

stopped quickly, position the engine control switch to 

the 

STOP

 position immediately.

WARNING

Internal pressure can build in the 

engine crankcase while the engine 

is running. Removing the oil fill plug/ 

dipstick while the engine is hot can 

cause extremely hot oil to spray out 

of the crankcase and can severely 

burn skin. Allow engine oil to cool for 

several minutes before removing the 

oil fill plug/dipstick.
Always perform maintenance in a well- 

ventilated area. Gasoline fuel and fuel 

vapors are extremely flammable and 

can ignite under certain conditions.

WARNING

Avoid accidentally starting the 

generator during maintenance by 

removing the spark plug boot from 

the spark plug. For electric start 

generators, also disconnect the 

battery cables from the battery 

(disconnect the black negative (-) 

cable first) and place the cables away 

from the battery posts to avoid arcing.

Allow hot components to cool to 

the touch prior to performing any 

maintenance procedure.

OPERATION 

MAINTENANCE 

Figure 10 - Engine Control Switch to - STOP

Figure 11 - Remote Stop - Hold Stop Button

BEFORE PERFORMING MAINTENANCE ON THE GENERATOR, REVIEW THE SAFETY SECTION  

STARTING ON PAGE 5, AS WELL AS THE FOLLOWING SAFETY MESSAGES.

ON

OFF

Summary of Contents for WGen12000



































Reviews:

No comments

Brands by name

Popular brands

Load more brands