Western Digital WDE2170 Technical Reference Manual Download Page 37 | Manualshive

Page: 37 / 54

background image

WD Enterprise WDE2170/WDE4360

The Option Block

4079-001045 Rev. B

RELEASED 04-08-97

29

5.3.

Option Block Pin Assignments

The option block is used to modify the drive characteristics. The table below shows the
pin numbers that correspond to each option or signal, and provides instruction for
enabling and disabling these features. Refer to the WD Enterprise Installation Guide
(document number 4079-001046) for option definitions.

Table 5-1. Option Block Pin Assignments

OPTION/SIGNAL

PINS

CONFIGURATION NOTES

SCSI IDs

1 - 8

Set according to Table 5-2.

(KEY)/LED-

X - 10

X - no pin/10 - LED cathode connection

RESERVED

11 - 12

11 - Ground/12 - Reserved

OPT 1: DISABLE AUTO START

13 - 14

Install jumper to disable auto start.

OPT 2: AUTO START DELAY

15 - 16

Install jumper to enable auto start delay.

OPT 3: SCAM

17 - 18

Install jumper to enable SCAM.

OPT 4: DISABLE UNIT ATTENTION

19 - 20

Install jumper to disable unit attention.

OPT 5: DISABLE TARGET INITIATED
SYNCHRONOUS/WIDE NEGOTIATION

21 - 22

Install jumper to disable target initiated
synchronous/wide negotiation.

OPT 6: SCSI TERMINATION

23 - 24

Install jumper to enable SCSI termination.

TXD/RXD

25 - 26

Reserved

TPWR/+5V

27 - 28

Install jumper to enable TERMPWR on the
SCSI bus.

LED+/+5V

29 - 30

29 - LED anode connection/30 - Reserved

+12R/+12R

31 - 32

Reserved

+12V/+12V

33 - 34

Reserved

Note:

Pins 1,3,5,7,11,13,15,17,19,21, and 23 are ground.

«
...
35
36
37
38
39
...
»

Summary of Contents for WDE2170























































Reviews:

No comments

Related manuals for WDE2170

Brand: IBM Pages: 18

Brand: IBM Pages: 180

Brand: IBM Pages: 102

Brand: Palram Pages: 74

Brand: U-Line Pages: 2

Cruizer Enterprise

Brand: SanDisk Pages: 10

Brand: Zhejiang Longyard Trade Industrial Pages: 18

SolarLEAF SL-1000

Brand: Yotta Pages: 13

EXOS ENTERPRISE ST10000NM001G

Brand: Seagate Pages: 56

InTANK iR2775-S3

Brand: Raidon Pages: 2

Brand: Supatool Pages: 2

Brand: XtendLan Pages: 124

Pro 2-Disk RAID USB and eSATA

Brand: Verbatim Pages: 56

Brand: WOOD feeling Pages: 27

Brand: Costway Pages: 4

Brand: CalDigit Pages: 14

LITTLE BIG DISK THUNDERBOLT 2

Brand: LaCie Pages: 35

TRAVELMATE 310 310

Brand: Viking Components Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands