Western Airconditioning DBIS-09 User Manual Download Page 26 | Manualshive

Page: 26 / 28

Western Airconditioning DBIS-09 User Manual Download Page 26

24

Error Analysis

If your conditioning unit runs abnormally, please check the following items before contact the
maintenance serviceman.

Note:

If the air conditioner still runs abnormally after the above check and handling, please contact
the maintenance serviceman at the local appointed service center.

Table 10

Errors

Possible causes

Failed starup

1. The power supply is not connected.
2. Electrical leakage of air-conditioning unit
causes tripping of the leakage switch.
3. The operating keys are locked.
4. Voltage is too low.

Stop after a short while of opration

The air inlet/outlet of the indoor/outdoor unit is

clogged.

Poor cooling effect

1. The air filter is dirty or blocked.

2. There is heat source or too many people
inside the room.
3. The door or window is open.
4. There is obstacle at the air intake or outlet.
5. The set temperature is too high.
6. There is refrigerant leakage.
7. The performance of room temperature
sensor becomes worse.

Poor heating effect

1. The air filter is dirty or blocked.
2. The door or window is not firmly closed.

3. The set room temperature is too low .
4. There is refrigerant leakage.

«
...
24
25
26
27
28
»

Summary of Contents for DBIS-09





























Reviews:

No comments