manualshive.com logo in svg

Westermo SDW-500, User Manual

Share
Download
Westermo SDW-500 User Manual Download Page 20

20

6644-2214

DIP switch settings SDW-541 and SDW-532

DIP-switches are accessible under the lid on top of the product. DIP-switches are used 
to configure the product.

NOTE

When configuration via DIP-switches, the settings of DIP-switches configure the product 
only after a reboot (power off/on). 

Observe this when the DIP-switches are configured:

…   Speed and duplex setting only valid when auto-negotiation is disabled.
…   When monitoring selected all outgoing packets from the switch is also copied to the 

port 1.

…   Speed and duplex switch settings are ignored for FX ports.
…   If auto-negotiation and auto MDI/MDI-X disabled all TX ports support MDI-X 

configuration.

CAUTION - ELECTROSTATIC DISCHARGE (ESD) 

Prevent electrostatic discharge damages to internal electronic 
parts by discharging your body to a grounding point (e.g. use a 
wrist strap).

WARNING - HAZARDOUS VOLTAGE

Do not open an energized product. Hazardous voltage may occur 
when connected to a power supply. 

Summary of Contents for SDW-500























Reviews:

No comments

Brands by name

Popular brands

Load more brands