Westermo GS-01 Installation Manual Download

Page: 50 / 56

6195-2201

6.0 LED Function

• LED Off

Device switch off – Not ready

• LED On

Device switched on – Connecting to network

• LED flashing slowly

Device switched on – Idle mode

• LED flashing rapidly

Device switched on – Transmission mode

7.0 Application examples

The AT-commands are used to configure the modems. The AT-commands can be sent from
a terminal or a PC with a terminal program (Hyperterminal, Procomm etc.) Make sure the
number of data bits is the same in both the modem and the terminal. Factory default in
GS-01 is 8,N,1 and the data rate is set to automatic baud rate detection.

These tests have been made with PC to modem cables, fully wired.
The modems/adapters have been factory default before any commands have been sent.

To restore factory settings type AT&F followed by AT&W.

To be able to get to the command mode when the modem is online, type +++
(no Enter) and wait. An OK will appear on the screen.
Type ATH to hang up. Type ATO to go online.
The connection can be shut down from both sides.
Hint! Always check the Signal Quality with AT+CSQ before dialling (See 8.3 b).

7.1 GS-01 to GS-01

Data between GS-01 and GS-01 with V.32 protocol

GS-01 in the dialling end

AT+CPIN=xxxx

Insert PIN number if required

AT+CBST=7,0,1

Bearer type selection. Choose data rate and protocol.
(9 600, V.32)

ATDxxxxxxxxxx

Dial the number

GS-01 in the receiving end

AT+CPIN=xxxx

Insert PIN number if required before expected call

AT+CBST=7,0,1

Bearer type selection. Choose data rate and protocol.

(9 600, V.32)

ATS0=1 or

Automatic answering after 1 ring signal

ATA

Answer a call

AT&W

Store active configuration

7.2 GS-01 to GS-01 with V.110 protocol for faster connection.

Same as above but replace AT+CBST=7,0,1 to:

AT+CBST=71,0,1

Bearer type selection, choose data rate and protocol.
(9 600, V.110)

AT&W

Store active configuration

Summary of Contents for GS-01

























































Search results

Summary of Contents for GS-01

Reviews:

Related manuals for GS-01

Brands by name

Popular brands

Westermo GS-01, Installation Manual

Search results

Summary of Contents for GS-01

Reviews:

Related manuals for GS-01

Brands by name

Popular brands