background image

Brush Crusher™

14

WESTENDORFMFG WJ123050 

Westendorf Manufacturing Co., Inc.

SECTION 5: SERVICE & MAINTENANCE

Perform scheduled maintenance as outlined below.

1. Lower the bucket or attachment to the ground, or re-

move on level surface to perform maintenance.

2. Turn off tractor engine, remove key, and set tractor 

parking brake before performing inspections.

Lubrication

Maintenance Checklist

Grease all zerks noted below every 10-12 hours.  Failure to grease the Brush Crusher may result in premature 

wear.  All zerks can be accessed with the loader on tractor, arms down and the attachment level.

WARNING

CRUSHING HAZARD. 

To prevent automatic movement:

•  Operate loader from the operator’s seat only.

•  Remain at the controls until the operation cycle is fully 

complete.

•  Lock-out valve “detent” when operating loader. See 

your tractor operator’s manual.

3. Relieve hydraulic pressure. Use wood or cardboard 

to inspect hydraulic hoses, lines and fittings for damage, 

wear and leaks. Repair or replace as necessary.

4. Inspect pivot pins for wear.  Be certain retaining roll 

pins are installed on each pin.

5. Check all mounting hardware for tightness. Use the 

torque charts in this section.

6. Lubricate BC-4300 grease fittings as shown below.

7. While in use, listen for abnormal or unusual sounds 

that may indicate worn, loose or damaged parts.

8.  After each use, clean loader and attachment and 

verify all safety decals are legible and not damaged. 

Replace damaged safety decals.

Summary of Contents for BC-4300
























Reviews: