background image

Assembly Instructions

Select Lab Fixed Height 

Workstation

Visit the Music Lab Workstations web page at www.wengercorp.com.

Contents

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety Precautions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Required Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Hardware Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Workstation Components  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Optional Rackmount Shelf Assembly . . . . . . . . . . . . . . . . . . . . . . 18

Note:

  Please read and understand these instructions before starting the assembly.

Note:

  If you need additional information, contact Wenger Corporation using the information below.

©Wenger Corporation 2018 

Printed in USA 2018-07 

Part #225D099-02

Wenger Corporation,

 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448

Questions? Call.....USA: (800) 4WENGER (493-6437) • Worldwide: +1-507-455-4100 • wengercorp.com

Summary of Contents for Select Lab Fixed Height Workstation





















Reviews: