background image

33

32

WARRANTY

WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this 

commitment and our dedication to quality.

LIMITED WARRANTY OF WEN PRODUCTS FOR HOME USE

GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power 

tools will be free from defects in material or workmanship during personal use for a period of two (2) years from date 

of purchase or 500 hours of use; whichever comes first. Ninety days for all WEN products if the tool is used for pro-

fessional or commercial use. Purchaser has 30 days from the date of purchase to report missing or damaged parts.
SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty and, to the extent per-

mitted by law, any warranty or condition implied by law, shall be the replacement of parts, without charge, which are 

defective in material or workmanship and which have not been subjected to misuse, alteration, careless handling, 

misrepair, abuse, neglect, normal wear and tear, improper maintenance, improper storage, incorrect lubricants/fuels, 

or other conditions adversely affecting the Product or the component of the Product, whether by accident or inten-

tionally, by persons other than Seller. To make a claim under this Limited Warranty, you must make sure to keep a 

copy of your proof of purchase that clearly defines the Date of Purchase (month and year) and the Place of Purchase. 

Place of Purchase must be a direct vendor of Great Lakes Technologies, LLC. Purchasing through third party vendors, 

including but not limited to garage sales, pawn shops, resale shops, or any other secondhand merchant, voids the 

warranty included with this product. Contact [email protected] or 1-800-232-1195 with the following 

information to make arrangements: your shipping address, phone number, serial number, required part numbers, 

and proof of purchase. Damaged or defective parts and products may need to be sent to WEN before the replace-

ments can be shipped out.
Upon the confirmation of a WEN representative, your product may qualify for repairs and service work. When re-

turning a product for warranty service, the shipping charges must be prepaid by the purchaser. The product must 

be shipped in its original container (or an equivalent), properly packed to withstand the hazards of shipment. The 

product must be fully insured with a copy of the proof of purchase enclosed. There must also be a description of the 

problem in order to help our repairs department diagnose and fix the issue. Repairs will be made and the product 

will be returned and shipped back to the purchaser at no charge for addresses within the contiguous United States.
THIS LIMITED WARRANTY DOES NOT APPLY TO ITEMS THAT WEAR OUT FROM REGULAR USAGE OVER TIME, 

INCLUDING FILTERS, SPARK PLUGS, VOLTAGE REGULATORS, BRUSHES, GASKETS, O-RINGS, WHEEL KITS, BAT-

TERIES, RECOIL STARTERS, HIGH PRESSURE HOSES, SPRAY GUNS, ETC. ANY IMPLIED WARRANTIES SHALL BE 

LIMITED IN DURATION TO TWO (2) YEARS FROM DATE OF PURCHASE. SOME STATES IN THE U.S. AND SOME 

CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE 

ABOVE LIMITATION MAY NOT APPLY TO YOU.
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT 

NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME 

STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IN-

CIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS 

WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY TO 

COUNTRY.
THIS LIMITED WARRANTY APPLIES ONLY TO ITEMS SOLD WITHIN THE UNITED STATES OF AMERICA, CANADA 

AND THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CON-

TACT THE WEN CUSTOMER SUPPORT LINE. FOR WARRANTY PARTS OR PRODUCTS REPAIRED UNDER WARRAN-

TY SHIPPING TO ADDRESSES OUTSIDE OF THE CONTIGUOUS UNITED STATES, ADDITIONAL SHIPPING CHARGES 

MAY APPLY.

Summary of Contents for GN4500





































Reviews: