manualshive.com logo in svg

Wen 3939, Instruction Manual, Page: 18 / 24

Share
Download
Wen 3939 Instruction Manual Download Page 18

TROUBLESHOOTING GUIDE

WARNING!

 Stop using the generator immediately if any of the following problems occur or risk serious 

personal injury. If you have any questions, please contact customer service at 

1-800-232-1195

 (M-F 8-5 CST), 

or email 

[email protected]

.

Problem

Possible Cause

Solution

Band saw will not start 

(no sound whatsoever).

Saw not plugged in.

Plug in saw.

Power switch turned OFF, or 

safety key not inserted.

Insert safety key and turn saw ON.

Improper size/length of exten-

sion cord.

Use proper extension cord. Refer to chart on p. 6.

Bad outlet.

Try another outlet, or have a qualified electrician check/

replace outlet.

Defective power switch.

Contact customer service (1-800-232-1195) for as-

sistance.

Band saw will not start 

(humming sound).

Blade overtightened.

Adjust blade tension properly (see "ADJUSTING BLADE 

TENSION").

Belt overtightened.

Adjust belt tension properly (see "ADJUSTING THE 

CUTTING SPEED").

Bad start capacitor.

Contact customer service (1-800-232-1195) for as-

sistance.

Bad motor bearing, or bad 

motor.

Contact customer service (1-800-232-1195) for as-

sistance.

Blade will not track

properly.

Blade is improperly ten-

sioned.

Adjust blade tension properly (see "ADJUSTING 

BLADE TENSION").

Tracking knob is over-

adjusted.

Adjust tracking properly (see "ADJUSTING THE 

BLADE TRACKING").

Blade is warped.

Replace the blade.

Tires are worn.

Contact customer service (1-800-232-1195) for as-

sistance.

Blade "drifts".

Blade is improperly ten-

sioned.

Adjust blade tension properly (see "ADJUSTING 

BLADE TENSION").

Blade is dull.

Replace blade.

Upper blade guard height 

improperly set.

Adjust upper blade guide height properly (see "RAIS-

ING AND LOWERING THE UPPER BLADE GUIDE").

Guide bearings improperly 

adjusted.

Adjust guide bearings properly (see sections on p. 

13).

Improper blade tracking 

setting.

Adjust tracking properly (see "ADJUSTING THE 

BLADE TRACKING").

Improper feed rate.

Do not force the workpiece. Let the tool do the work.

Blade is warped.

Contact customer service (1-800-232-1195) for as-

sistance.

18

Summary of Contents for 3939

























Reviews:

No comments