Wells WV-2HGRW Operation Manual Download Page 15 | Manualshive

Page: 15 / 32

background image

INSTALLATION (continued)

13

CAUTION:
Burn Hazard

DO NOT OPERATE UNLESS

THE GREASE DRIP TRAY

IS INSTALLED.

Moisture will drip into the hot
cooking surface causing
splattering of hot liquids.
Serious injury can result from
contact with hot splatter.

GREASE DRIP TRAY INSTALLATION

1. Install the GREASE DRIP TRAY on the hanger brackets, directly
below the grease baffle.

INSTALL COOKING APPLIANCE COMPONENTS

1. HOTPLATE (spiral elements only)
      a.    Lift/rotate the elements up.
      b.    Install one DRIP PAN in each hotplate well.
      c.    Install one ELEMENT SUPPORT in the indents in each DRIP
              PAN.
      d.    Rotate elements back into operating position.

2. If appliance is equipped with the optional warmer drawers:
a. Install WARMER PANS on warmer drawer rails.
b. Insert Humitrol racks (if provided).

Fig. 7 Hotplate Drip Pan Installation

Fig. 8 Roll Warmer Drawer Pan Installation

«
...
13
14
15
16
17
...
»

Summary of Contents for WV-2HGRW

































Reviews:

No comments

Related manuals for WV-2HGRW

Brand: TECHWOOD Pages: 9

Brand: SCHOLTES Pages: 13

Brand: Parkinson Cowan Pages: 53

Brand: Vigan Mammoth Pages: 44

Brand: Tricity Bendix Pages: 36

Brand: Tricity Bendix Pages: 36

Kenmore Refrigerator

Brand: Sears Pages: 12

Brand: Virtus Pages: 95

Brand: Indesit Pages: 64

Brand: Gaggenau Pages: 31

Brand: STEININGER Pages: 25

Brand: Pkm Pages: 47

Brand: DCS Pages: 28

Brand: Sienna Pages: 16

Brand: ILVE Pages: 16

Brand: ILVE Pages: 40

Brand: HAEGER Pages: 32

Brand: EAS Electric Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands