background image

INSTALLATION 

    4. 

For “top-mounted”  warmers (i.e. warmers mounted from above 

  the 

counter 

top): 

 

 

a.  Verify that provided sealants are applied to the underside 

 

 

 

of the warmer top flange prior to setting the unit into the  

   cutout. 
  b. 

After 

installation, 

verify 

that the tabs on the Wellsloks are 

 

 

 

turned out to lock the warmer into the counter 

 

 

c.  Apply a thin bead of food-grade silicone sealant around the 

 

 

 

flange to seal it to the counter. 

 

 

d.  Wellslok extension kits are available for installing warmers 

 

 

 

in counter tops  where the standard Wellslok would not  

 

 

 

normally reach.  The extension kit will adapt to counter  

 

 

 

tops up to 1¾” thick. 

 

ELECTRICAL INSTALLATION

 

 
     1. 

Refer to the product nameplate.  Verify the electrical service  

 

 

power.  Voltage and phase must match the nameplate    

 

 

specifications.  Wiring the warmer to the wrong voltage can  

 

 

severely damage the unit or cause noticeably decreased  

  performance. 

 

 

     2. 

Available electrical service amperage must meet or exceed the  

 

 

specifications listed on the specification sheet provided with the 

 

 

warmer. 

     3. 

Warmer and control unit must be connected to an appropriate 

 

 

building ground.  Ground connection will be marked “GND” or

 

 

”       " . 

 

 

 

NOTE: 

 Wire gauge, insulation type and temperature rating , as 

 

well as type, size and construction of conduit, must meet or exceed  

 

applicable specifications of local codes and of the National        

 Electrical 

Code. 

 

PLUMBING INSTALLATION 

 

 

For use in the State of Massachusetts, this appliance must be   

 

installed in compliance with 

Massachusetts Fuel Gas and  

 

Plumbing Code CMR 248.

 

 
     1. 

IMPORTANT: 

 All plumbing installations must be performed by 

  a 

qualified 

plumber. 

     2. 

For units equipped with a DRAIN LINE:  Some jurisdictions  

 

 

may require an approved air gap or other back-flow  

 

 

prevention device in the drain.  It is the responsibility of the  

 

 

plumber to determine such requirement, to provide and       

 

 

properly install the required device. 

 

 

NOTE: 

 Damage caused by 

leaks due to improper 
installation is NOT covered by 
warranty.  

 

 

CAUTION: 

SHOCK  HAZARD 

 

The ground lug of this         
appliance must be connected 
to a suitable building ground. 
 

IMPORTANT: 

Contact a licensed electrician 
to install and connect         
electrical power to the         
appliance. 

 

IMPORTANT: 

Damage due to being 
connected to the wrong     
voltage or phase is NOT    
covered by warranty. 

 

IMPORTANT:

  Electrical      

installation other than as 
specified on the specification 
sheet will void the UL  listing, 
and may void the warranty.  
 

NOTE:  

Plumb connections 

must be made in compliance 
with all Federal, State and  
Local Plumbing Codes and 
Ordinances.

 

M

012C.03  2M

-308031 

  Owne

rs M

anual fo

r Three

-W

e

ll 

In

f.Sw

. M

O

D

W

armer

s

 

Summary of Contents for MOD-300D

















Reviews: