background image

2M-308017-01

1C Built-In Single W

ell Modular W

armer w/T

-Stat Control

2

FEATURES & OPERATING CONTROLS 

A. THERMOSTAT

1. On thermostatically controlled warmers, power is applied to the

heating element according to the control knob position and the

actual temperature at the temperature sensing thermobulb.

2. The desired temperature is controlled by rotating the temperature

control knob.  The knob has a numeric scale, where higher

numbers correspond to higher temperature.

3. On warmers equipped with an indicator light, the light will glow

when the thermostat is calling for heat (i.e. the element is

energized).

4. The TEMPERATURE CONTROL KNOB will rotate approximately

300º, and will reach a “stop” at both ends.

The OFF position is marked.

NOTE:

  The dial position is an indication of the temperature setting.  

Actual temperature will vary depending upon the type of product 

and food consistency.

B. MOUNTING

1. MOD-series built-in warmers may are equipped with wellsloks,

uniquely designed turnout tabs which help secure the warmer top

flange to the countertop.

2. See the Installation Instructions, supplied with the particular

appliance, for details.

C. DRAINS

1. Suffix “D” units (e.g. MOD-300TD) have drains for each pan,

with each pan having an individual drain valve.

IL2469

WELLSLOKS

INDICATOR

LIGHT

TEMPERATURE

CONTROL

KNOB

IL2468

Summary of Contents for MOD-100T

























Reviews: