Wellis SAMOA User Manual Download Page 25 | Manualshive

Page: 25 / 32

background image

SENSOR-RELATED MESSAGES

Sensor Balance is Poor – M015
The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service.

Sensor Balance is Poor* – M026
The temperature sensors ARE out of sync. The Sensor Balance is Poor fault has been established for at
least 1 hour. Call for Service.

Sensor Failure – Sensor A: M031, Sensor B: M032
A temperature sensor or sensor circuit has failed. Call for Service.

MISCELLANEOUS MESSAGES

No Communications
The control panel is not receiving communication from the System. Call for Service.

Pre-Production Software
The Control System is operating with test software. Call for Service.

°F or °C is replaced by °T
The Control System is in Test Mode. Call for Service.

* This message can be reset from the topside panel with any button press.

«
...
23
24
25
26
27
...
»

Summary of Contents for SAMOA

































Reviews:

No comments

Related manuals for SAMOA

CalderaSpas Utopia Series

Brand: CalderaSpas Pages: 16

Brand: Garden Leisure Pages: 24

Solares Smart Spa

Brand: ab Pages: 40

PureSpa SPJ-H-10-2

Brand: Intex Pages: 21

Brand: Jacuzzi Pages: 2

2005 ProTech LED Series

Brand: Jacuzzi Pages: 47

Brand: Jacuzzi Pages: 44

Brand: Jacuzzi Pages: 80

Brand: Balboa Water Group Pages: 2

DESIGNER BATH SERIES

Brand: Jacuzzi Pages: 28

Brand: EAGO Pages: 9

Catalina Luxury Armstrong

Brand: aqua living Pages: 8

Brand: Aleko Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands