WELCH-ILMVAC DUOSEAL 1374 Owner'S Manual Download Page 26

26

THE INFORMATION HEREIN IS GIVEN IN GOOD FAITH, BUT NO WARRANTY, EXPRESS OR IMPLIES, IS MADE.

Revision Date: 03/31/09 

                   Rev. A 

P/N: 67-0254

6 of  7

SECTION 13 – DISPOSAL CONSIDERATIONS 

Hazard characteristic and regulatory waste stream classification can charge product use.  Accordingly, it is the 
responsibility of the user to determine the proper storage, transportation, treatment and/or disposal 
methodologies for spent materials and residues at the time of disposition. 

Conditions of use may cause this material to become a hazardous waste, as defined by Federal or State regulations.  It 
is the responsibility of the user to determine if the material is a hazardous waste at the time of disposal.  Transportation, 
treatment, storage and disposal of waste material must be conducted in accordance with RCRA regulations (see 40 
CFR 260 through 40 CFR 271).  State and/or local regulations may be more restrictive.  Contact the RCRA/Superfund 
Hotline at (800) 424-9346 or your regional US EPA  office for guidance concerning case specific disposal issues. 

SECTION 14 – TRANSPORT INFORMATION 

DOT Status: 

Not regulated by the U.S. Department of Transportation as a hazardous material. 

Proper Shipping Name:

 

Not 

regulated 

 

   

Hazard Class:

 

 Not 

regulated     

Packing Group(s):

 Not 

applicable 

UN/NA ID:

   Not 

regulated   

Reportable Quantity:

 

A Reportable Quantity (RQ) has not been established for any  
components of this material. 

Placards:

  Not 

applicable. 

Emergency Response 
Guide No.:

    

Not applicable. 

HAZMAT STCC No.:

 2911990 

MARPOL III Status: 

Not a DOT “Marine Pollutant” per 49 CFR 171.8 

SECTION 15 – REGULATORY INFORMATION 

TSCA Inventory:  

This product and/or its components are listed on the Toxic Substance Control Act (TSCA)  

 Inventory. 

SARA 302/304:  

The Superfund Amendments and Reauthorization Act of 1986 (SARA) Title III requires  
Facilities subject to Subparts 302 and 304 to submit emergency planning and notification  
information based on Threshold Planing Quantities (TPQs) and Reportable Quantities(RQs)  
for “Extremely Hazardous Substances” listed in 40 CFR 302.4 and 40 CFR 355.  No  
components were identified.  

SARA 311/312:

  

The Superfund Amendments and Reauthorization Act of 1989 (SARA) Title III Requires  
facilities subject to this subpart to submit aggregate information on chemicals by “Hazard  
Category” as defined in 40 CFR 370.2. This material would be classified under the  
following hazard categories :No SARA 311/312 Hazard categories identified. 

SARA 313:  

This product contains the following components in concentrations above the minimis levels
that are listed as toxic chemicals in 40 CFR Part 372 pursuant to the requirements of  

 

 

Section 313 of SARA: No components were identified. 

CERCLA:

The Comprehensive Environmental Response, Compensation, and Liability Act of 1980  
(CERCLA) requires notification of the National Response Center concerning release of  
quantities of “hazardous substances” equal to or greater than the reportable quantities (RQs)  
listed in 40 CFR 302.4.  As defined by CERCLA, the term “hazardous substance” does not  
include petroleum, including crude oil or any fraction thereof which is not otherwise  
specifically designated in 40 CFR 302.4.  This product or refinery stream is not known to  
contain chemical substances subject to this statute.  However, it is recommended that you  
contact state and local authorities to determine if there are any other reporting requirements  
in the event of a spill. 

Summary of Contents for DUOSEAL 1374





























Reviews: