Welch Allyn Propaq LT 802LT0N Service Manual Download Page 32

Page: 32 / 80

Disassembly and reassembly

Welch Allyn Propaq LT Vital Signs Monitor

Insert the flex cable into the connector.

Slide the latching piece toward the connector body until it clicks into place.

Connector locations

Caution

Do not attempt to remove a flex cable until the ZIF latch has been

opened.

Caution

Never attempt to disconnect any cable by pulling on the cable wires.

Always disconnect cables by grasping and pulling only on the connector halves.

Connector

Connects with:

Connector

Connects with:

Main Board

Charging Cradle - Interconnect Board

ECG (flex)

Cradle power board (3-conductor)

On/Off Switch

Cradle power board (10-conductor)

SpO

(flex)

JP1

External USB

Display module

Propaq LT Monitor

BDM

Charging Cradle - Cradle Power Board

PCMCIA (radio) card

I/O panel (DC input)

Button pad

Cradle interconnect board (10-conductor)

Battery pack

Cradle interconnect board (3-conductor)

Pump/bleed valve

Radio Card

J10

Dump valve

(flex)

Antenna

J11

Speaker

Power/USB (flex)

Summary of Contents for Propaq LT 802LT0N

















































































Search results

Summary of Contents for Propaq LT 802LT0N

Reviews:

Related manuals for Propaq LT 802LT0N

Brands by name

Popular brands

Welch Allyn Propaq LT 802LT0N, Service Manual

Search results

Summary of Contents for Propaq LT 802LT0N

Reviews:

Related manuals for Propaq LT 802LT0N

Brands by name

Popular brands