Welbilt Convotherm mini black easyTouch 10.10 Installation Manual Download Page 96

Page: 96 / 148

3.4

Hazards and Safety Measures When Moving the Unit

Safety hazard: moving heavy loads

When moving or transporting the unit, keep the following hazards in mind and take the actions re‐

quired in order to eliminate and/or minimize these hazards:

Risk / hazard

Where and in which situa‐

tions will the risk/hazard ex‐

ist?

What to do

Safety device

Risk of injury due to ex‐

cessive exertion

Whenever moving the unit

■

Use appropriate lifting

equipment

■

Do not lift or carry too

much weight!

■

Use carrying straps

■

Wear the required per‐

sonal protective equip‐

ment

None

Safety hazard: mechanical unit components

When moving or transporting the unit, keep the following hazards in mind and take the actions re‐

quired in order to eliminate and/or minimize these hazards:

Risk / hazard

Where and in which situa‐

tions will the risk/hazard ex‐

ist?

What to do

Safety device

Crush hazard for all

body parts if the unit

falls down

Whenever moving the unit

■

Use appropriate transpor‐

tation equipment

■

Transport equipment

slowly and carefully and

secure it in such a way

that it cannot tip over

■

Keep the unit's center of

gravity in mind

■

Avoid bumping into ob‐

jects

None

Crush hazard for all

body parts if the unit

falls down or topples

over

When setting the unit down

on the surface on which it will

be resting

Observe all the require‐

ments concerning the sup‐

porting surface at all times

while setting up the unit.

Please refer to Installation

Location Requirements on

page 41

None

3 For Your Safety

Installation Manual

Summary of Contents for Convotherm mini black easyTouch 10.10





















































































































































Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands

Welbilt Convotherm mini black easyTouch 10.10, Installation Manual

Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands