Welbilt Convotherm mini black easyTouch 10.10 Installation Manual Download Page 104

Page: 104 / 148

3.8

Hazards and Safety Measures When Removing the Unit from

Service

Safety hazard: electricity

When removing the unit from service, keep the following hazards in mind and take the actions re‐

quired in order to eliminate and/or minimize these hazards:

Risk / hazard

Where and in which situa‐

tions will the risk/hazard ex‐

ist?

What to do

Safety device

Risk of electric shock

posed by live parts

■

Under covers

■

Under the operating panel

■

Work on the unit's electri‐

cal components should

be performed exclusively

by a qualified electrician

from an authorized cus‐

tomer service company

■

Work professionally

Covers

Before removing the cov‐

ers:

■

De-energize all connec‐

tions

■

Lock out and tag out all

switches

■

Wait 15 minutes so that

the DC bus capacitors

can discharge fully

■

Make sure that the unit is

de-energized

Safety hazard: moving heavy loads

When removing the unit from service, keep the following hazards in mind and take the actions re‐

quired in order to eliminate and/or minimize these hazards:

Risk / hazard

Where and in which situa‐

tions will the risk/hazard ex‐

ist?

What to do

Safety device

Risk of injury due to ex‐

cessive exertion

Whenever moving the unit

■

Use appropriate lifting

equipment

■

Do not lift or carry too

much weight!

■

Use carrying straps

■

Wear the required per‐

sonal protective equip‐

ment

None

3 For Your Safety

Installation Manual

Summary of Contents for Convotherm mini black easyTouch 10.10





















































































































































Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands

Welbilt Convotherm mini black easyTouch 10.10, Installation Manual

Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands