manualshive.com logo in svg

WEISS GAMBIT DS1-MK2, Operating Manual, Page: 12 / 30

Share
Download
WEISS GAMBIT DS1-MK2 Operating Manual Download Page 12

OPERATING  INSTRUCTIONS  FOR  GAMBIT  DE-ESSER/COMPRESSOR DS1-MK2

OPERATION

-

 Weiss Engineering Ltd., Florastr. 42, CH-8610 Uster

Page  12 of 29

 +41 1 940 20 06    

2

 +41 1 940 22 14    

8

 http://www.weiss.ch    

*

 [email protected]

Parallel Compressor

The DS1-MK2 can be used as a parallel compres-

sor, where the compressed signal is added to the

straight signal.

How to activate parallel compression:

 Touch

the gain / data controller (

Í

). In the menu that

appears, mark the checkbox with softkey B.

When using parallel compression, the DS1-MK2 is

able to run in frequency selective or in full band

mode.

Graphic 10: Parallel full band compression

Parallel full band compression

: As can be seen

in the schematic (Graphic 10), the input signal and

the compressed signal are added together. The

gain makeup value can be used to control the

amount of compressed signal. The pre-limiter gain

can be used to scale the mix before limiting.

Graphic 11: Parallel band selective compression

Parallel band selective compression

 (Graphic

11): To add even more subtle compression, the

compressed signal can be filtered before com-

pression. Using the monitor function, one can

listen to the filtered signal for optimal crossover

setup.

Why parallel compression?

Read this quote from Bob Katz from the Master-

ing Webboard:
“You want a patch that compresses without

stomping on the attacks at all, preserves tran-

sients but gives you great inner detail? ...
You have one control, one control only, and that

is the output level of the compressor [gain

makeup], the ‘sidechain’. You can bring out inner

details without losing breathing, and hardly af-

fecting the upper dynamics at all. Works great.

Not just great, absolutely fantastically. Fattens

bass instruments without causing breathing or

pumping. You name it, it works very well.
Variations: Use it like the Dolby Spectral Enhan-

cer, by split band [parallel] compression, so that

(for example) high frequency inner details at low

levels are enhanced. ” The last paragraph refers

to parallel band selective compression (crossover

in highpass mode).

In-
put

Comp.

output
meter

input
meter

peak / over
hold

Out-
put

Safety
Limiter

+

Pre-Limiter
Gain

Output
Gain

x

x

In-
put

Comp.

output
meter

input
meter

peak / over
hold

Out-
put

Safety
Limiter

+

Output
Gain

Cross-
over

band
pass

Pre-Limiter
Gain

x

x

Summary of Contents for GAMBIT DS1-MK2































Reviews:

No comments